Factory adjustments that should be verified: 1. Outfeed Table Height (page 31) 2. Depth-of-Cut Scale (page 32) 3. Fence Stops (page 32) G0526 6" Jointer -21 SECTION 6: OPERATIONS General Your safety is important! Please follow the warnings below during this entire section: Damage to your eyes, lungs, and ears could result from failure to wear safety glasses, a dust mask, and hearing protec- tion while using this machine. Loose hair and clothing could get caught in machinery and cause serious per

.. .. .. .. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .. .. .... .... .... Column Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION P0643001 KNURLED KNOB PSS01M SET SCREW M6-1 X 10 P0643003 DEPTH CONTROL PSB02M CAP SCREW M6-1 X 20 P0643005 WING SCREW M6-1 X 35 PSB11M CAP SCREW M8-1 X 16 PW01M FLAT WASHER 8MM PSB14M CAP SCREW M8-1.25 X 20 P0643009 DEPTH CONTROL MOUNT P0643010 LIFTING EYE BOLT P0643011 COLUMN PSB33

The material flow exceeds the atomizing cap capacity. 2. Inlet air pressure is too low. 3. Material is too thick. 1. Lower fluid flow. 2. Increase inlet air pressure. 3. Thin material. Narrow center pat- tern. 1. Volume control turned in too far. 2. Inlet air pressure too high. 3. Fluid pressure is too low. 4. Material is too thin. 1. Increase volume. 2. Reduce inlet air pressure. 3. Increase fluid pressure. 4. Adjust material. No spray output. 1. No pressure at gun. 2. Fluid passages dirty. 3.

Build-up of material inside atomizing cap. 1. Clear holes. 2. Clean. 3. Clean. Heavy deposit of material in center. 1. The material flow exceeds the atomizing cap capacity. 2. Inlet air pressure is too low. 3. Material is too thick. 1. Lower fluid flow. 2. Increase inlet air pressure. 3. Thin material. Narrow center pat- tern. 1. Volume control turned in too far. 2. Inlet air pressure too high. 3. Fluid pressure is too low. 4. Material is too thin. 1. Increase volume. 2. Reduce inlet air pressur

Read through this entire manual to become familiar with the controls and operations before starting the machine! ss3il-k ¡§iUf jjg£ 1 Ifl Awarning Wear safety glasses during the entire setup process! Awarning This machine and its components are very heavy. Get lifting help or use power lifting equipment such as a fork lift to move heavy items. Unpacking Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and insp

Use the shims that came with the scoring blade set (Figure 38) to stack the scoring blade to the same thickness as the main blade. Figure 38. Typical scoring blade with shims. 5. Install the blade set with the teeth facing the opposite direction as the main blade, then reinstall the arbor flange and the arbor nut. 6. Place a hex wrench in the hole in the arbor and use the arbor wrench to tighten the arbor nut as shown in Figure 39. Note: The arbor nut has right-hand threads and tightens by turni

Do not use the angle vise for milling. It is made strictly for holding materials to be drilled. This vise will not adequately clamp an object safely for a milling operation. There is not enough clamping pressure available and objects may be pulled out or upset in the vise jaws causing cutting tools to break and/or parts to be thrown. Any attempt to perform a milling operation using this vise may result in personal injury. DO NOT make adjustments while the Mill/Drill is running. Ensure that the s

Support rod and column installed onto bottom shelf. Continued on next page COPYRIGHT © JULY, 2008 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL10942 PRINTED IN CHINA 2. Repeat Step 1 with the remaining support rods (see Figure 3), making sure to install the two 20" rods on the front end and the 205/8" rods on the back end of the shelf. Note: The longer rods will install into