2. Separate a section of hair about 1 . " wide. Hold the dryer ( detangling comb facing out) under the section of hair and place it at the roots ensuring that the teeth penetrate the hair fully. 3. Gently pull the dryer to about 1" from the roots and turn under: this will give the action of the Tourmaline Ceramic ™ and flocked disks maximum effect. 4. Hold the dryer parallel to your scalp for 5 seconds. 5. Then slide the appliance slowly towards the ends. 6. Repeat if necessary and finish with a

Close the battery compartment cover. Remember • Keep the battery compartment dry. Warning • Use only alkaline batteries. • DO NOT mix old and new batteries. • DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium) batteries. Essential Oil usage • Do not ingest. • Keep away from eyes. • Use only as directed. • Do not inhale. Cleaning and care • Pad may be washed in warm soapy water and air dried. If replacement pads are needed, please call customer service at 1

This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If is still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If is still does not fit, contact a qualified

Unscrew the valve in the center of the base. Fill container by holding container under a source of running cold water until the container is filled to the desired level. Do not overfill. Screw the valve cap onto the water container and return the container to the upright position. Place the water container onto the base and make certain it is seated properly in the cavity. DO NOT FILL THE CONTAINER WITH HOT WATER. OPERATING THE STEAMER Make sure the On/Off switch is in the off 1.position. Make s

Incoming voltage and current must match the electrical specifications on the pump data plate and serial tag. Check for proper rotation of the pump after power has been connected and before operation. Install vacuum lines to loader stations and the dust collector. Connect the dust collector vacuum outlet to the pump inlet. INSTALLATION AND OPERATION NOTE: The pump inlet is equipped with a vacuum relief valve to prevent the vacuum from exceeding 12 in. Hg. Excessive vacuum will reduce the life of

Of course, other sections of the extrusion line also influence the quality of the extruded product. This section does not provide solutions to problems originating with other equipment on the extrusion line. Additional troubleshooting help can be found in the manufacturer’s manuals included with this User Guide. UGE058/0803 CTS Saw TROUBLESHOOTING 6-3 ELECTRICAL PROBLEMS Symptom Saw will not start Saw blade runs backwards Look in this section when you have problems such as lights on the contro

If is still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. This unit has a two-wire double-insulated polarized plug USER/MAINTENANCE INSTRUCTIONS 1. Make sure foot bath is unplugged and is in the OFF position. 2. When transporting foot bath, position hands around rubberized handles for most secure grip. 3. Place foot bath on floor, fill foot bath with warm or cold water, and plug into wall outlet. Never plug in or unplug the foot ba

If they do not, press CLEAR MSG to clear these indicators manually. CONTRAST BUTTON Contrast can be altered when on hook by pressing the Contrast button on the display. There are 8 contrast levels. REPROGRAMMING NETWORK SERVICE BUTTONS CALL FORWARD ON, CALL FORWARD OFF or CALL WAITING OFF can be reprogrammed if your telephone company requires a different code. Simply follow the instructions for programming speed dial on the following page. If you do not have one or both of these functions, these

Any unanswered calls which have not been viewed are marked with a < * >icon at the centre of the bottom line of the display. 1. Press to access the call list. OR Press

The purpose of this test is to allow you to make sure the water sensing system (ALCI) is working. 1. Plug in the appliance and press test button on plug (See appropriate diagram below). 2. The appliance will stop working. There will be an audible click and reset button will pop out. 3. To reset ALCI with a reset button, unit should be unplugged. Then push reset button in, and reinsert plug into outlet. Test Reset Test Reset 4. If ALCI is not functioning properly, return appliance to nearest serv