PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. General Safety Information ▲warnings WARNING: Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning. DANGER: Carbon monoxide poisoning may lead to death! Carbon Monoxide Poisoning: Early signs of carbon mono

The surface must be level. Protect generator from heavy dust, sand, dirt, rain, or snow. Do not locate generator near standing water and snow. Make sure area is well-vented. Only responsible adults should use generator. Never let anyone operate generator without proper instructions. NOTE: If oil level is too low, oil alert system will keep engine from starting (See “Oil Alert System,” page 5). Make sure oil level is full before starting. See “Engine Oil,” page 10. Before starting the engine, dis

Underside: Bottom of bowl undercoated to prevent condensation and deaden sound. Self-rimming: Sink is furnished with appropriate number of clamps to provide a watertight installation. OTHER Drain opening: 3-1/2". Faucet holes: Available with 3 faucet holes only, 4" center to center. Note: Sinks only available in multipacks of 18. Model DPR1812522 SINK DIMENSIONS (INCHES)* Model Number Overall Inside Each Bowl Cutout in Countertop (11/2" Radius Corners) Number of 11/2" Dia. Faucet Holes

Self-rimming. DESIGN FEATURES Bowl Depth: 7" (large bowl), 5-1/8" (disposer bowl). Coved Corners: 3" vertical and 2-1/4" horizontal (large bowl), 1-3/4" horizontal (small bowl). Finish: Exposed surfaces are polished to a satin finish with highshine bowl radius. Underside: Fully undercoated to prevent condensation and deaden sound. OTHER Drain opening: 3-1/2". NOTE: Unless otherwise specified, sink is furnished with 4 faucet holes as shown. These sinks do NOT comply with ASME A112.19.3-2

Width is front to back. D-Prefix sinks are packed one per shipping carton. Sink bowl is fully undercoated. D6-Prefix sinks are nested 6 units per shipping carton. Sink bowls are sound deadened on bottom only. D50-Prefix sinks are nested 50 units per shipping carton. Sink bowls are sound deadened on bottom only. 3 4 |*-4"^<- 4"^t- 4"->| -1-1/4" -C ■ E is Bowl Depth Model D225194 Illustrated E is Bowl Depth Model D233194 Illustrated D C A ALL DIMENSIONS IN INCHES, TO CONVERT TO MILLIME

If you see globules of water in the bottom, drain and flush the tank and filter with clean fuel, b. Refill with fresh, clean fuel. FORM 5S1792 MODELS 2E510A, 2E511 A, 3E218A & 3E219 01582. Trouble Shooting Chart (Continued) SYMPTOMS POSSIBLE CAUSE(S) CORRECTIVE ACTION Heater burns, but puffs 2. Dirty air filters causing reduced 2. Remove and clean the air filters. of smoke can be seen; air flow through nozzle, resulting Be sure air intake is not blocked. heater will not burn in low

Warranty void if damage to the product results from the use of a part other than a genuine Coleman ® part. COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE OF UNAUTHORIZED PARTS OR SERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION

4. Remove and wash in clean fuel. Blow dry and replace. 5. a. Clean by blowing compressed air through nozzle from outlet end of nozzle. b. Replace nozzle if cleaning does not solve the problem. 6. Move heater to warmer environment until fuel flows freely. 7. Be sure air filters are clean. 8. Check fuel filter for air leaks and for tightness of fit where it is connected to fuel line. Ignition Troubles WARNING: DISCONNECT HEATER CORD! HIGH VOLTAGE! Heater will not ignite, but motor runs for a

NO. DESCRIPTION PART NO. QTY. REF. NO. DESCRIPTION PART NO. QTY. 1 2 3 4 Upper shell Screw, #10-16 x 1/2" Combustion chamber assembly Photocell bracket 098511-64 M15823-27 098512-07 M16660 1 8 1 1 27 28 29 30 Bushing Bushing Screw, #10-16 x 1/2" Clip nut M30865-02 M50104-02 M11084-27 M11271 -8 1 1 5 6 7 8 Screw, #6-32 x 3/8" Photocell assembly Burner assembly Screw, #10-16 x 1/2" M10908-2 M16656-4 ■ t M11084-27 1 1 31 32 33 34 Screw, #8-18 x 1/4" Fuel tank Fuel cap (includes gasket) Flame out

Install the wheels (6) on the axle. IMPORTANT: The extended hub of the wheel should be positioned to- " ward the wheels support frame. Position the cap nuts (9) on the axle ends and gently tap with a hammer to secure. 2. Position the heater on the wheel support frame assembly with the combustion chamber end over the wheels. 3. Use four screws (7) and nuts (8) to attach the front handle to the top of the tank flange. The screws will go through the front handle, the tank flange and the wheel su