Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Wash filter assembly in clean fuel and inspect for damage. Note: It is not necessary to remove filter from filter assembly on Model T70. On Model T115 and T165 assembly is one piece. 5. Install filter assembly and bushing (Model T70) into fuel tank. IMPORTANT: Be sure filter (Model T115 and T165) and bushing (Model T70) are firmly seated in tank. 6. Connect fuel line and install side cover. Model T70 B C A Model T115 and T165 C A B 107351-01 19 Periodic Service STORAGE LOCATION AND MAINTENANCE Note:If shipping, transport companies require fuel tanks to be empty. 1. Drain fuel tank. Note:Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed. 2. Replace drain plug if provided. 3. If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir, and drain again. This will prevent excess debris from clogging filters during future use. 4. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. Check with local automotive service stations that recycle oil. 5. If storing, store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT:Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. When taking heater out of storage, perform the following maintenance procedures. Refer to Periodic Servicesection, page 13. CAUTION: Check for bird, wasp, and rodent nests and other foreign matter. Check for leaks. Inspect the electrical cord for deterio ration and damage. Clean fan. Clean flame sensor. Clean exterior of unit. Fill with proper fuel. Do not oil air filter, pump vanes, or rotor. 107351-01 20 Assembly UNPACK COMPONENTS B E A D C A -Axle, Hardware, B -Heater D -Wheel Support Frame E -Rear Handle and Wheels C -Front Handle Remove components from shipping carton and check for damaged or missing parts. INSTALLING NOSE CONE GUARD IMPORTANT: THIS IS NOT TO BE USED AS A HANDLE. (For T70 Model Only) This model is furnished with a nose cone guard (A). Nose cone guard and mounting screws are found in the shipping carton. 1. Place nose cone guard on top of upper shell flange (B). Make sure nose cone guard is on hot air outlet end of heater (C). 2. Insert screws through nose cone guard and upper shell flange. 3. Tighten screws firmly. 4. Assemble wheels and handles per the instructions that follow. Model T70 Only A C B 107351-01 21 Assembly ATTACHING WHEELS AND AXLE 1. Install cap nut (A) onto end of axle (B). A B 2. Slide wheel (A) onto axle (B) with extended side of wheel hub away from cap nut. 3. Install axle on wheel support frame (C). 4. Install wheel (A), with extended side of wheel hub toward wheel support frame (B) onto axle (C). 5. Install cap nut (D) onto axle. A-Wheel B-Wheel Support Frame C-Axle D-Cap Nut A B C C A D B 107351-01 22 Assembly ATTACHING HEATER AND HANDLES 1. Install heater assembly (A) to wheel support frame (B). Align holes in heater assembly and wheel support frame. Note:Wheels are to be at hot air outlet end of heater on T70 ONLY (see next picture below). 2. Install fuel gauge cap (C). A C B 3. Install rear handle (A) using screws (B) and lock nuts (C). DO NOT TIGHTEN. Model T70 Shown A B C 4. Install front handle (A) (excluding T70) using screw (B) and lock nuts (C) DO NOT TIGHTEN. 5. Tighten all screws and nuts. B A C 107351-01 23 Specifications Model T70 Model T115 Model T165 Output rating 70,000 BTU/Hr 115,000 BTU/Hr 165,000 BTU/Hr (20.51 kW)) (33.70 kW) (48.35 kW) Hot air output (approximate) 360 cubic feet 490 cubic feet 575 cubic feet per minute per minute per minute (611 m3/HR) (830 m3/HR) (977 m3/HR) Fuel Kerosene or Kerosene or Kerosene or No. 1 Fuel Oil No. 1 Fuel Oil No. 1 Fuel Oil Voltage 120 AC 120 AC 120 AC Cycle 60 Hz. 60 Hz. 60 Hz. Amperage (starting) 5.75 7.5 7.5 Amperage (normal operation) 2.8 3.6 3.6 Motor Speed 3,450 rpm 3,450 rpm 3,450 rpm Weight (empty) (approximate) 37 lbs. (17 kg) 49 lbs. (23 kg) 56 lbs. (26 kg) Length 34 in. (864 mm) 41 in. (1042 mm) 46 in. (1170 mm) Width 15 in. (380 mm) 19 in. (480 mm) 22 in. (560 mm) Height 20 in. (510 mm) 22 in. (560 mm) 25 in. (635 mm) Fuel tank capacity 5.0 U.S. gal. 9.0 U.S. gal. 13.5 U.S. gal. (18.93 L) (34.07 L) (51.10 L) Fuel consumption 0.50 gal. (1.89 L) 0.85 gal. (3.22 L) 1.2 gal. (4.54 L) per hour per hour per hour Motor 1/8 hp (93.2 W) 1/5 hp (149.1 W) 1/5 hp (149.1 W) Pump air pressure 4.7 psi (32.41 kPa) 5.3 psi (36.54 kPa) 5.6 psi (38.61 kPa) (0.324 bar) (0.365 bar) (0.386 bar) (Specifications and design subject to change without notice.) 107351-01 24 Serial Number Identification SERIAL NUMBER PLATE LOCATION The space heater serial number (A) is located on rear of fuel tank. When ordering parts, always give your dealer the model and serial number. For your convenience, record this information below. JOHN DEERE PORTABLE SPACE HEATER Model No. ___________...
Эта инструкция также подходит к моделям:Электрообогреватели - and T165 (8.5 mb)