Wayne-Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’s Manual before you attempt this installation. To avoid possible injury, read the enclosed instructions carefully before installing and operating the garage door. Pay close attention to all warnings and notes. After installation is complete, fasten this manual near garage door for easy reference. The Quick Start Guide and Installation Instructions and Owner’s Manual are available at no charg

for single spring applications, there will be no left hand spring in the TorqueMaster ® spring tube assembly. lift the TorqueMaster® spring tube assembly and rest it on top of the flag angles. NOTE: Cable drum assemblies are marked right and left hand and consist of a cable drum and drum wrap. Cable drums and TorqueMaster® spring tube assembly are cam shaped to fit together only one way. Starting on the right hand side, slide the drum wrap over to access the counterbalance cable. Pre-wrap the ca

CAUTION: Over tightening the screws could deform plastic case. FORCE ADJ. PROGRAMSW STATUS IMPORTANT: CONNECT THE LOW VOLTAGE WIRE TO THE WALL STATIONS USING A “J” HOOK CONFIGURATION. IF WIRE IS COMPLETELY LOOPED AROUND TERMINAL SCREW, IT CAN PREVENT PROPER CONTACT. Wall Station Back Phillips Head Screws Wall Station Front Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll F

If door is not completely closed, turn travel knob 1/4 turn “more”. Repeat as necessary. NOTE: 1/4 turn equals 1” of door travel. 20 Setting Door Opening Travel OPEN CLOSE MORE LESS MORE TRAVEL ADJUSTMENT Bottom Of Opener Tools Needed: Flat Tip Screwdriver The door opener is assembled with the open travel adjustment preset for a typical door, but all doors should be adjusted to stop as close as possible to the door’s “natural” fully open, resting position. To determine the door’s “natural” fully

341785 REV1 08-03-2009 Low Head Room Front Mount Torsion Spring Installation Instructions and Owner’s Manual 9800 Series - 4 Section IMPORTANT NOTICE! Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. Wayne-Dalton Corp. P.O. Box 67 Mt. Hope, OH 44660 Definition of key words used in this manual: INDICaTEs a POTENTIally hazaRDOus sITuaTION WhICh

MOUNT THE SENDING UNIT (UNIT WITHOUT LED) ON THE SIDE WHICH IS EXPOSED TO THE MOST SUN. SUNLIGHT MAY AFFECT THE SAFETY SENSORS, AND THIS ORIENTATION WILL HELP REDUCE THE EFFECT. c. Attach the sending and receiving safety sensors to the “U” brackets by inserting all three tabs into the respective holes. Wall Mounting Bracket 5” Washer Nut 1/4”-20 x 1/2” Carriage Bolt 5/16” x 1-1/2” Lag Screw Door Jam U-Bracket Wall Mounting Bracket Receiving Unit LED a c b 11 Wired Infrared Safety Sensor Installa

Pay close attention to all instruction steps and notes. This manual should be retained for future reference. Table of contents Package Contents ....................................................................................................................... 2 Introduction............................................................................................................................... 2-3 Installation .............................................................................

If in question about any of the procedures, do not perform the work. Instead, have a trained door systems technician do the installation or repairs. IMPORTANT SAFETY NOTICES An overhead door is a large heavy object that moves with the help of springs under high tension. Moving objects and springs under tension can cause injuries. For your safety and the safety of others, follow these instructions: 1. Wear protective gloves during installation to avoid possible cuts from sharp metal edges. 2. It

Repeat for other section(s) except top section. IMPORTANT: PUSH & HOLD THE HINGE LEAFS AGAINST SECTION WHILE SECURING WITH (2) 1/4” -14 x 5/8” SELF TAPPING SCREWS. END AND INTERMEDIATE HINGES HAVE (2) SCREWS. NOTE: Install lock at this time (sold separately) see Side Lock installation instructions on page 25. 8 Power Drill 7/16” Socket Driver 9 Top Bracket Slide To install the top bracket slide, align the slots in the top bracket slide with the set of holes under the top sections u-bar. Loosely

Plug the motor power cord into the opener. lEFT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED RIGhT haND END OF TORquEMasTER® sPRING TuBE RIGhT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED PluG-IN MOTOR POWER CORD MOTOR 17 Tools Needed: None Tools Needed: idrive® Installation NOTE: see idrive® main installation and owners manual for idrive® parts. IMPORTANT: RIGhT aND lEFT haND Is alWays DETERMINED FROM INsIDE ThE GaRaGE lOOkING OuT. lay the TorqueMaster® s