If the gas control is turned to the “OFF” position or gas flow to the appliance is shut off, the pilot cannot be relighted until the safety magnet is deenergized (approximately 60 seconds). There will be an audible “click” when the safety magnet in the gas control is de-energized. Pilot can now be relighted. Repeat steps 5 through 9. 11. Turn gas control knob counterclockwise to “ON”. 12. Turn on all electric power to the appliance. (If applicable) 13. Replace access panel (front panel). Set the

See Figure B. Maintain equal distance between spring spacers. 3. Remove the 6-." dia. Vent collar from the fireplace. Replace this collar with the 7" dia. Flex Vent adapter collar provided with the vent kit. 4. Slide the Flex Vent flue pipe into the Outer Flex Vent pipe. 5. Install the Wall Firestop/Thimble assembly as required through the wall. Refer to the venting charts in the fireplace manual to determine the proper height and size of the vent opening. The minimum opening should be 9" wide b

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number LS-18P 15999 LS-24P 15970 LS-30P 15970 Platinum Bright Embers PE-20-1 Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18, 24, 30)P Logs Figure 5 Attention: Do not use Figures 1 to 5 to order replacement logs. Refer to Page 11, Parts List and

Warning: ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS. Improper installation or use of the fireplace can cause serious injury or death from fire, burns, explosions, or carbon monoxide poisoning. Page 6 25613-0-0309 25613-0-0309 Page 7 Figure 1 LEFT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW ELECTRICAL ACCESS VENT COLLAR TOP VIEW GAS LINE ACCESS A C J G I GAS LINE ACCESS H D E B VENT COLLAR STANDOFFS NAILING FLANGES GLASS FRAME ASSEMBLY GAS LINE ACCESS RATING PLATE AND LABELS GAS CONTR

(2.68kPa) for the purpose of input adjustment to a maximum of 14.0" w.c. (3.484kPa). *NOTE: Remote "RF" Models - 10.5" w.c. maximum Figure 7 25613-0-0309 Page 9 Page 10 25613-0-0309 Framing and Finishing 1. Choose unit location. 2. Frame in fireplace with a header across the top. It is important to allow for finished face when setting the depth of the frame. 3. Attach fireplace to frame using adjustable nailing flange. Preset depth to suit facing material (adjustable to 3/8", 1/2" or 3/4" depths

Consumer: Please retain these instructions for future use. Log sets comply with ANSI Z21.11.2 Unvented Heaters and also comply with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of log sets in a vented configuration. Check your state or local codes. WARNING: If not installed, operated and maintained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combus

15997-0-0903 Page 5 Page 6 15997-0-0903 LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). Page 715997-0-0903 LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not c

21 Logs Parts List & Parts View ....................................................................................................................... 22 Service Notes................................................................................................................................................ 23 Installer: Please leave these instructions with the consumer. Consumer: Please retain these instructions for future use. 12409-2-0403 Page 2 IMPORTANT SAFETY INFORMATION IMPORTANT SAFE

Page 4 15997-0-0903 Do not cover any large rear ports with LS-18FA(C,O,S)-1 PHOTOS Photo 4Photo 3Photo 1 Photo 2loose material (glowing embers). 15997-0-0903 Page 5 Page 6 15997-0-0903 LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). LS-24FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Photo 1 Photo 2Do not cover any large rear ports withloose material (glowing embers). Page 715997-0-0903 LS-30FA(C,O,S)-1 PHOTOS Photo 3 Photo 4 Phot

3. The right, middle log (#3) will go directly on the two pins on the right side of the flat portion of the main burner. 4. The left, middle log (#4) should be placed flat on the pin on the left side of the flat portion of the main burner. The left, 2 1 Log Placement VFYR and VFYM -(18, 24, 30)SO Logs Shown Figure 13 middle log will rest on a pin located on the right, middle log. 3 4 RWO Curing Process The logs shipped with this product are formed from a cast refractory material. The curing proc