INSTALLING THE DISC SANDER TABLE 1. Thread an M8 x 1.25 x 20mm hex socket head screw (A) Fig. 10 partially into the hole in the base of the sander. Insert the rod (B) into the hole. Align the flat of the rod (B) with the screw (A). Tighten the screw (A). 2. Slide the table assembly (C) Fig. 11 on the rod (B). 3. Thread an M8 x 1.25 x 20mm hex socket head screw (A) Fig. 11 into the hole in the table support bracket. Align the flat on the rod (B) with the screw (A). Tighten the screw (A). Fig. 10

Ee .«.©.d eEYREG a«..e hCG ajQEOE .VGoZCG ‘ ea.YG .Goia°SG .aj ;OLCEJ .VGoZCG hCG ;.E.gE’G hCG .Goia°S’G A.°ud ea.YG .Vo©aj aNjoZ OG.e hCG AE«°TCG ae«af ..a.d ea.YG .Vo©aj ;cOG.M hCG OZ .UEi°TCG a.°SG.H ea.YG iO°UEG adhEfi .aj ™HEadG afE«°udG .joa hCG ojo.a©YG afE«°udG AOch .o.jO ofBG .OH acoud Eo.J ¤EG eEa– ±.°S ,.E.°†dG OL.A aNdE.e Eo.ad ...Ah .o.a©YG afE«°udG .«ch hCG ™FEN.d AGoudG .«dO .ON oe o.a©e afE«°U .«ch UobCG ™b.e ..Y ±o©adG .G..©dG ‘ ».eYG o.jO ofBG .OH Oa.e ..Y .E°uJ’G ..«dodG Gog ‘

These are available at your Black & Decker Dealer. We recommend No. 16 AWG wire size for length up to 100 feet, and No. 14 AWG or larger wire size for longer lengths. Always inspect your extension cord for loose or exposed wires and damaged insulation. DO NOT use a damaged cord with your, mower . ASSEMBLY 1, Open carton and remove cardboard fillers and plastic hardware bag(s) (contents shown in Figure 1). FIGURE 1 ■ Note: 680551-01 Wheels (4) not in bag. E 2. Without removing mower from c

This means that it is constructed throughout with TWO separate “layers” of electrical insulation or one DOUBLE thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your Drill is equipped with a two-prong plug which permits you to use extension cords without concern for maintaining a ground connection. NOTE DOUBLE-INSULATION does not take the place of normal safety precautions when operating t

. do not use outdoors. . do not let cord hang over edge of table or counter, or touch hot surfaces. . do not place on or near a hot gas or electric burner, or in a heated oven. . extreme caution must be used when moving an appliance containing hot oil or other hot liquids. . Always attach plug to appliance first, then plug cord in the wall outlet. To disconnect, turn any control to oFF, then remove plug from wall outlet. . do not use appliance for other than intended use. SAVe tHeSe iNStrUctiONS

The cut-off stock remains on the table and is not touched until the saw blade has stopped, unless it is a large piece allowing safe removal. When ripping boards longer than three feet, use a work support at the rear of the saw to keep the workpiece from falling off the saw table. 2. If the ripped work is less than 4 inches wide, a push stick should always be used to complete the feed, as shown in Fig. 41. The push stick can easily be made from scrap material as explained in the section Fig. 41 “

SAVE THESE INSTRUCTIONS Safety Instructions • Do not operate the laser in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. • Use the laser only with the specifically designated batteries. Use of any other batteries may create a risk of fire. • Store idle laser out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained users. • Use only accessories that are recommended by the manufacturer for your model. Accessories tha

X Do not use the screwdriver as a pry bar in any position. Switching on and off (fig. E) X To switch the tool on, press the on/off trigger switch (7). X To switch the tool off, release the on/off trigger switch (7). A forward/reverse and lock-off button (8) determines the direction of the tool and also serves as a lock off button. X To select forward rotation, release the on/off trigger switch (7) and move the forward/reverse and lock-off button (8) to the left, looking forward. X To select reve

Longest life and best performance can be obtained if the batteries are charged at normal room temperatures. 2. While charging, the charger will normally become warm to the touch. 3. If the batteries do not charge properly : a. Check house current at receptacle by plugging in a lamp or other appliance. b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. c. If house current is okay and you do not get proper charging, contact your nearest