1). Wiring Diagram FIG. 1 DAS-LLC Line Level Converter Installation Instructions 1. Connect a small run of 16/4 between the zone output on the Matrix Audio controller and the connector labelled “From Zone” on the DAS-LLC. 2. Connect the 16/4 wire run from the zone's keypad to the connector labelled “To Keypad” on the DAS-LLC. 3. Connect a stereo RCA cable from the Left and Right RCA jacks labelled “To Amplifier” on the DAS-LLC to the RCA inputs on the external amplifier. 4. Connect a smal

Refer to the Protected Setup Navigation Buttons section on page 58 for more detailed information. Video Settings Page The Video Settings page (FIG. 40) sets the Video properties of the incoming video signal. You can access this page by pressing the Video button on the Setup page. This page contains four tabs across the top for each source input on the unit. If you are using a TPI-PRO-2, slots 3 and 4 appear greyed out. These source inputs are labeled at the rear of the unit. For each source inpu

BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO LICENSEE. • U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph ©(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs ©(1) and (2) of the C

When done, complete the insertion of the remaining housing latches. 4. Verify that the notches along the bottom of the plastic battery slot separator strip also fit into the three provided alignment holes on the circuit board. 5. Firmly press down around the entire rim of the outer housing to snap the cover back into place. Be careful not to pinch the antenna wire in the housing. 6. Use a grounded Phillips-head screwdriver to insert and re-secure the two housing screws removed in Step 1. 7. Inse

1 Specifications.................................................................................................................. 2 The Mio Attaché Wake Up State.............................................................................. 3 Mio Attaché Docking Station.................................................................................... 3 Specifications.................................................................................................................. 3 Install

1 MVP-7500 Wireless Touch Panel (FG5965-01) ATTENTION! Verify the NetLinx Master Firmware is build 117 or greater for the ME260 and NI-Series Controllers. Verify the TPDesign4 program being used is Version 2.2 or higher. Earlier versions of the Master firmware and TPD4 software are incompatible with these panels. Overview The AMX MVP-7500 panel (FG5965-01) uses an internal wireless compact flash card to communicate with a NetLinx Master via an off-the-shelf 802.11b Wireless Access Point. MVP uni

18). As the screw is tightened, the clip bends toward the insertion hole and into the wall. This bending creates a "grip" on the wall by either pressing onto the wall or by securing the drywall between the housing and the drywall clip. The most important thing to remember when mounting the wall box is that the outer trim must be installed flush against the mounting surface. FIG. 18 provides recommended cutout dimensions for the wall box. It is recommended that you cutout the surface slightly sma

.. From the Online Tree tab of the Workspace window, select the NetLinx Master. .. Follow steps outlined in either the Obtaining or Assigning the Master’s IP Address sections from your particular NetLinx Master instruction manual to use an address. .. Note the IP Address and Gateway information. 2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc > NetLinx Studio > NetLinx Studio 2.3). 3. Select Settings > Master Communication Settings, from the Main menu to ope

This is the only method of programming the TPI/3 using Serial Commands. • AXlink connection: Connect a DB-9 cable from your PCCOM port to the Programming port on the Controller. Then use an AXlink cable to connect the AXlink connector on the Controller to the AXlink connector at the rear of the AXB-TPI/3. This is the only method of programming the interface unit using Send_Commands. Included Accessories • Two rack-mount ears and a package of rack screws • One 4-pin AXlink connector • One 2-pin P

AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS OTHERWISE LIMITED BY APPLICABLE LAW, AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS, SPECIFICATIONS, WARRANTIES, PRICES, AND POLICIES WITHOUT NOTICE. Table of Contents Table of Contents Overview ............................................................................................................1