Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
This is the only method of programming the TPI/3 using Serial Commands. • AXlink connection: Connect a DB-9 cable from your PCCOM port to the Programming port on the Controller. Then use an AXlink cable to connect the AXlink connector on the Controller to the AXlink connector at the rear of the AXB-TPI/3. This is the only method of programming the interface unit using Send_Commands. Included Accessories • Two rack-mount ears and a package of rack screws • One 4-pin AXlink connector • One 2-pin PWR connector Weight 4.85 lbs (2.20 kg) VTM-D15/A 15" MultiMedia Touch Panel Systems MultiMedia Touch Panel VTM-D15/A 15" MultiMedia Touch Panel Systems 9 AXB-TPI/3 Components FIG. 3 shows the front and rear components of the AXB-TPI/3 Touch Panel Interface 3. FIG. 3 AXB-TPI/3 (front and rear views) 12VDC SLOT 2 SLOT 1 TP3-VID COMP Y/C TP3-VGA VGA R TP3-RGB AXlink GND AXP AXM MOUSE PORT PWR SLOT 3 PWR MONITOR OUT R G B H V G B H/HV V Slot 3 (shown with TP3-VGA module) Slot 2 (shown with optional TP3-RGB module) Slot 1 (shown with default TP3-VID module) Mouse port Monitor Out (VGA-HD15) Monitor Out (5 BNC) controlling RGBHV 12 VDC power connector AXlink connector VGA SVGA XGA AXlink PORT PROGRAM Rack-mounting brackets VGA output LED SVGA output LED XGA output LED AXlink LED DB-9 Program Port Front View Rear View optional to VTM-D15/A (connection to TouchScreen signal cable MultiMedia Touch Panel VTM-D15/A Sample Configuration FIG. 4 shows a sample Table Top MultiMedia System application using a TPI/3, touch panel, computer (used to configure the TPI/3), and Central Controller. AMX PSN6.5 Power Supply 2-pin captive-wire DB-9 to 8-pin mini-DIN AMX AXB-TPI/3 (front view) AXlink 4-pin External Power (Adapter and Cord) 15-pin VGA cable DB-9 connecting Program Port from TPI/3 to COM1/2 on rear of computer connection to Master Controller AMX AXB-TPI/3 (rear view) VTM-D15/A MultiMedia Touch Panel (showing optional input cards) Computer FIG. 4 Sample MultiMedia Touch Panel System Configuration Power to the VTM-D15/A touch panel is supplied through an external power supply. Power to the TPI/3 can be supplied either directly through a PSN6.5 or indirectly through an AXlink cable connection from a Central Controller. The power source is dependant on the distance between the TPI/3 and the Central Controller. If the distance between the two is greater than outlined in the Wiring the AXB-TPI/3 section on page 18, a local power source (like the PSN6.5) must be used. VTM-D15/A 15" MultiMedia Touch Panel Systems Installation and Wiring Installation and Wiring This section covers the steps necessary to setup the individual MultiMedia components and connect them together. The three areas of focus ar the main component setup, wiring, installation, and connection. Setting up the AXB-TPI/3 The AXB-TPI/3 does not come pre-installed with any input modules. The card provided with the original system package is the TP3-VID Composite/S-Video Input Module. The TPI/3 can be configured with any combination of 3 input cards (TP3-RGB, TP3-VGA, and/or TP3-VID). Installing the input modules 1. Discharge the static electricity from your body by touching a grounded metal object. Always power down the TPI/3 before attempting to remove or install input modules. Failure to do so could result in damage to the TPI/3 and/or input modules. 2. Disconnect any connectors from the AXB-TPI/3. 3. Remove (counter-clockwise) the two-black thumbscrews on the slot cover corresponding to the location being used for the inserted input module. Any module can be inserted into any slot number. 4. Gently insert the module into the brackets inside the card slot and slide the input module into the enclosure until you feel it contact the slot connector, as shown in FIG. 5. FIG. 5 Inserting an input module 5. Screw in (clockwise) the two thumbscrews to secure the module. 6. Repeat steps 3 through 5 to insert other input modules, if necessary. Removing input modules 1. Disconnect any power supply connected to the TPI/3. Always power down the TPI/3 before attempting to remove or install input modules. Failure to do so could result in damage to the TPI/3 and/or input modules. VTM-D15/A 15" MultiMedia Touch Panel Systems Installation and Wiring 12 VTM-D15/A 15" MultiMedia Touch Panel Systems 2. Discharge the static electricity from your body by touching a grounded metal object. 3. Disconnect any other connectors from the TPI/3 input module. 4. Remove (counter-clockwise) the two black thumbscrews on the input module. 5. Slide the module out of the enclosure. 6. Repeat steps 4 and 5 for other slots, as required. 7. Ensure that all thumbscrews are secured and reconnect all rear panel connectors. Mounting the TPI/3 in an equipment rack Use the supplied mounting brackets for 19" equipment rack installations. Remove the mounting brackets for flat surface installations. You will need a Phillips screwdriver to install the TPI/3. To install the AXB-TPI/3 in an equipment rack: 1. Discharge the ...