Note:IfyouhaveaDishantennasystemalreadyinstalled,andthedishhasbeen pointed forthe strongest possible signal strength, you can skip this chapter and go directly to Appendix A to install the satellite receiver in an existing system. Installing a DISH 500 Antenna The first step in installing your dish antenna is to assemble the satellite dish, mount it,and point it in the general direction of a satellite. To do this, follow these instructions: Finding the Satellites You need to find the satellites

2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with a dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades wi

(not the receiver remote control or the menus displayed by the receiver), turn off the closed captioned feature. The TV screen is displaying a DISH Network logo. • Your TV1 or TV2 outputs are not on. • Press the SELECT or blank POWER button on the remote control. The TV screen is all blue. • You may have connected the receiver to an input on the TVthat is incorrect for the signal output from the receiver. • Check your TV owner’s manual for the correct TV input to use for the signal output from t

• PCM Only - Select this option only if the stereo system or amplifier cannot decode Dolby Digital signals. • Dolby Digital/PCM - Select this option only if the stereo system or amplifier can decode both Dolby Digital and Linear PCM signals. The audio output is also dependent on what is present in the program you are watching. The table below shows what type of output you will hear: Signal Present in Program Optical Output Setting Dolby Digital PCM Both Dolby Digital Only Dolby Digital PCM Dolby

Note: You can program this button to control the volume on a TV or amplifier. See Using TV or Amplifier Volume Control later in this chapter for instructions. Guide Button Press the GUIDE button to open the Program Guide. When the Program Guide is open, press this button to switch among Favorites Lists. Arrow Buttons When using a menu, press these buttons to move the highlight to an option. • When watching a program, press the RIGHT ARROW button to open the Browse Banner or the UP or DOWN ARROW

You may also order DISH Network pay-per-view Services by calling 1-877-DISH-PPV (3474-778) and using our automated system, or speaking with a live operator at one of our customer service centers; in either case, a fee will apply as detailed in Section 2(D). Pre-Pay Promotion customers may only order pay-perview Services by calling 1-877-DISH-PPV (3473-778). G.Accessing the Internet Through Your Receiver. Some of our receivers can be used to access websites and information on the Internet. Neithe

Unless changed, factory default for TV2 is channel 60. Refer to the "How to Watch TV on TV2" section in this guide for correct channel setup or use the RECOVER button. Your satellite receiver is in "Single Mode" and "Shared View" is disabled. To watch what TV1 is watching, simply enable the Shared View option. To watch a program on TV2 that is different than what is being viewed on TV1, press the MODE button on the front of the satellite receiver to put it in Dual Mode. See your User's Guide fo

Compliance Information Statement EchoStar Technologies Corporation, 94 Inverness Terrace East, Englewood CO., (303) 706-4000, declares that: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digi

Refer to the "How to Watch TV on TV1" section in this guide for the correct input. Why doesn't my PIP button seem to work? You can only view Picture-In-Picture when in Single Mode. Press the MODE button on the front of your receiver so that the Single Mode light is on, then use the blue PICTURE-IN-PICTURE buttons as desired. What should I do if my remote control doesn't seem to operate my satellite receiver? • Try pressing the SAT Mode button. • Check to make sure you are using the correct rem