Войти: › Operation in either NBX Call Control mode or Session Initiation Protocol (SIP) › Redundant, hot-swappable power supplies; optional redundant hard disks (RAID1) › Standard four ports by 400 hours AA/VM, scalable up to 72 ports › Dual 10/100 uplink ports; 100 Mbps backplane › Four-slot expansion chassis for additional analog stations or trunks (T1/E1, PRI, BRI, Analog) › 1,500 device capacity (stations/trunks) › SIP-ready for applications and devices *Available in North America and Mexico only.
3. Make sure the power cord is correctly and securely connected into the HomePortal. 4. Verify that both ends of the power cord are firmly plugged into the brick. Note: If the POWER indicator light is red (signifying a system error), or does not light after performing the steps above, contact 2Wire Customer Care. BROADBAND LINK indicator light is red If the BROADBAND LINK indicator light is red, the HomePortal has not established a connection to your DSL service provider: 1. Go to the HomePortal
ACCUSYS, INC. 5F, 38 TAIYUAN ST, JHUBEI, HSINCHU, TAIWAN, R.O.C. TITLE EXPERAID COMMAND LINE INTERFACE USER GUIDE PROJECT “DESKTOP RAID” DOCUMENT STATUS OFFICIAL RELEASE REV. G–05-NOV-2007 PAGE 20 OF 27 3.3.4.3 Command Name Command Description RebuildParity Use this command to rebuild parity of an array which contains parity. i.e. RAID 5 or RAID 6. Parameter 1 Parameter Description Array No.:
You can change these values as needed. 29 To enable the DHCP server for dynamic IP address allocation to the clients, select the “Enable” check box. The clients can get their IP address from a range of IP Pool Addresses. The Lease Time is the amount of time a client will be allowed to connect to the Router using the assigned IP address. You can enter your local domain name in the Local Domain Name field. 2-3-2 DHCP Client List The DHCP client list allows you to see which clients are connected to
WARNING: The “warning” icon is followed by information alerting you to a potential situation that may cause damage to property or equipment. CAUTION: The “caution” icon is followed by information warning you that a situation has the potential to cause bodily harm or death. Service Information The user should not attempt any maintenance or service on the unit beyond the procedures outlined in this document. Any initial hardware setup problem that cannot be resolved at your internal organization s
¦ The 20-port 10/100BASE-TX Fast Ethernet Layer 2 Switching Module (Model Number 3CB9LF20R) has twenty 10/100 Mbps RJ-45 ports on its front panel and two 1-Gigabit ports on the back for connection to the chassis backplane. Each of these FEN Switching Modules operates as a Layer 2 switch and occupies a single switching module slot in the CoreBuilder 9000 7-slot chassis, 8-slot chassis, or 16-slot chassis. The 10/100BASE-TX and 100BASE-FX FEN Switching Modules support the following key features: ¦
ADVANCED APPLICATIONS › Voice messaging: 400 hours of voice storage standard (non-SIP mode) › IP Messaging: advanced NBX in SIP mode voice messaging; ships with find me/follow me service and 12 ports enabled (scalable in one-port increments) › IP Conferencing: hosted bridge for NBX in SIP mode for scheduled and ad-hoc conferences (standard 25-seat license) › Desktop Call Assistant (DCA) : on-screen dialing and contact management software › Complement Attendant Software (CAS) : desktop applicatio
This window is used for blocking group members’ access to specified URLs and/or for letting group members access specified URLs blocked at the minimum filtering level. Fig. 3:1-13 Exception URL window NOTE: Settings in this window work in conjunction with those made in the Override Account window and in the Minimum Filtering Level window maintained by the global administrator. Users with an override account will be able to access URLs set up to be blocked in this window, if the global administra
SAVE SET, BAUDRATE SET, ADDRESS SET, KEY LOCK and CLEAR SAVE DATA function. We will describe the details as follows. 2.3.6.1 Set up the maximum output voltage When you select the MAX VOLTAGE SET function, the LCD will display as: MAX VOLT. = 24.00 VYou can set the voltage value by using the number kaypad or rotating the ROTARY knob. Then confirm NEW= the value by pressing “Enter” button. 2.3.6.2 Set up the maximum output power When you select the MAX POWER SET function, the LCD will display as:
