Contact Gazco for further information. IMPORTANT The chimney must be swept before installation. Do not attempt to burn rubbish on this fire. This fire has a naked flame. A suitable guard should be used for the protection of young children, the elderly or infirm. This appliance is intended for decorative purposes only. Please read these instructions carefully and keep them in a safe place. They will be needed when servicing the fire. The commissioning sheet on page 3 MUST be completed by the Inst
4.3 Replace with a new ignition lead following the same route as the old one. Replace the valve cover and the pilot assembly. 4.4 Check operation of the new ignition lead. 5.1 The piezo assembly used on this appliance is not serviceable and is unlikely to fail. 5.2 If a new piezo is required it will be necessary to change the gas valve. Refer to Section 6. SERVICING INSTRUCTIONS REPLACING PARTS 4. IGNITION LEAD AND PIEZO 5. PIEZO 3. PILOT UNIT 5 6 7 8 AR0915 AR0916 22 6.1 Turn the gas supply off
and Serial No. 13.1 Parts of this appliance become hot during normal use. It is recommended that a suitable fire guard be used for protection of young children and the infirm. Indeed, all parts of the appliance should be treated as a ‘working surface’ except for the control area. USER INSTRUCTIONS 7. GAZCO FLUE SURE SYSTEM 8. THE FLAME FAILURE DEVICE 9. 'RUNNING IN' 10. SERVICING 11. VENTILATION 12. INSTALLATION DETAILS 22 13. HOT SURFACES AR0390 10 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICAT
The volcanic stone should be placed directly on top of the firebox bottom, along the slope and to the back at the right and left sides of the burner. Position any ceramic fiber liners before placing the stone. Logs can be positioned after the volcanic stone. 12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. SUPERIOR® DIRECT-VENT GAS FIREPLACES • MODELS SLDVT-30/35/40/45 • CARE AND OPERATION INSTRUCTIONS Figure 7 4. Placement of Glowing Embers - Separate the Embers (rockwool) into pieces about
............................................................................... ............................................................................... Contact No............................................................... Date of Purchase....................................................... Model No................................................................. Serial No. ................................................................. Gas Type...................................
. Place the center log (C) as shown. The 2 notches on the bottom of log (C) fit over the corresponding locating brackets. 4. Place the left log (B) as shown. The top fork on log (B) fits into the notch on log (A). The bottom of log (B) rests on the subfloor. 5. Place the top right log (D) as shown. The top fork on log (D) fits into notch on log (A) as shown. The bottom fork on log (D) rests on subfloor flange (identified in photo #1). SSBV-4035 -Install as Follows Carefully position the ceramic
10.1 Turn the gas supply off at the isolation device. 10.2 Locate the aeration plate on the underside of the airbox and remove the Nyloc nut, see diagram 15. 10.3 Remove the plate and replace with the correct size, ensure that the hole(s) in the plate align correctly with the holes in the underside of the airbox and replace the Nyloc nut. 11.1 In order to change between gas types, it will be necessary to change the following items. • Pilot Unit • Control Valve • Main Injector • Aeration Plate (i
The centrepiece of any home, a Gazco fire adds warmth and character to a room or living space - even if you don't have a chimney! Whether you want to achieve an up-to-the-minute, contemporary look, or have your heart set on a more traditionally-designed fire, this brochure will help you make the perfect choice, whatever your style or budget. Front Cover: Studio 1 Pienza Open with White Stone fuel bed Contents Your Home Studio Fires Edge Bauhaus Profil Steel Studio 22 Andes, Inca, Geilo & Kepler
3. Locate the two (2) latches at the top of the control compartment. To disengage the two latches from the bottom vee-flange of the glass enclosure panel, reach for the handles located towards the back of the latches and pull the handles down toward the front of the appliance. 4. Swing the bottom of the door out and raise it slightly to lift the top flange of the door frame away from the appliance. Installing Glass Enclosure Panel (see Figure 11 ) 1. Visually inspect the gasket on the backside o
ANY ATTEMPT TO USE A DIFFERENT LOG SET IN THE FIREPLACE WILL VOID THE WARRANTY AND WILL RESULT IN INCOMPLETE COMBUSTION, SOOTING, AND POOR FLAME QUALITY. WARNING: LOG SET GETS VERY HOT AND WILL REMAIN HOT UP TO ONE HOUR AFTER GAS SUPPLY IS TURNED OFF. HANDLE ONLY WHEN LOG SET IS COOL. TURN OFF ALL GAS TO THE APPLIANCE BEFORE INSTALLING THE GRATE AND LOG SET. Electronic Appliance Checkout Electronic Appliance Checkout tions on page 14 and 15. Ensure the ignitor lights the pilot. The pilot flame s