ANTENNA 40. INPUT JACK 41. AUDIO MUTE SWITCH 42. LOW BATTERY INDICATOR 43. POWER ON/OFF SWITCH 44. INPUT VOLUME LEVEL 45. IR RECEPTOR SENSOR 46. BATTERY COMPARTMENT 47. LATCHING BATTERY DOOR 48. BELT CLIP/REAR OF UNIT 39 40 41 42 43 44 45 46 47 48 49 49. LAVALIERE MICROPHONE 9 SELECTING THE GROUP/CHANNEL, IR PROGRAMMING, AND SIMULTANEOUS MULTICHANNEL OPERATION (Note: The transmitter should be turned ON and ready for the IR communications with the receiver IR receptor for the following process.)
System choices consist of a 800-channel PLL-synthesized UHF Receiver with either a handheld microphone or lavaliere microphone and body-pack transmitter. Headset microphone available. WIRELESS SYSTEMS UHT800 UDR800 UBP800 UDR800• Sleek metal housing with internal antenna for optimum aesthetics and durable long life •Uni-directional neodymium dynamic cartridge for optimum sound, maximum feedback rejection, and minimal handling noise • Audio mute switch allows convenient audio muting while leaving
BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED.Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or consequential damages (including, but
18-1/2" Long; 4 oz. • Cardioid pickup pattern • Clean, accurate vocal reproduction with low ambient noise • Integral breath/wind filter • 250-ohm Impedance • Frequency response range of 50 Hz to 18 kHz • Sensitivity of -65 dB +/- 3 dB • Snap-on windscreen • Durable all-metal case with non-glare black finish • 5-1/2" adjustable lower stalk, with 9-1/2" rigid upper section Industrial Gooseneck Microphone MGN19 • Omni-directional pickup pattern • Rugged, reliable design for quality, long-term use u
Eyelets (x2) 11. Mounting Screws (x4) 12.Wire Exit Slot 13. Conduit Knockout (x2) 1 HFCS1Rear Drawing (terminal cover) Installation The HFCS1 can be installed in a variety of ceiling environments.The use of the TBCR (Tile Bridge Support Ring) accessory may be desired for many of these environments. For suspended ceilings, the use of a TBCR is strongly recommended to help support and distribute the weight of the speaker. In new construction installations, the TBCR, installed before sheetrock, act
Other switches are at installer’s discretion. STATION ACCESS Set switches in black as indicated. Other switches are at installer’s discretion. 1 0 1 0 1 0 The contact closure contact set is provided to signal to external equipment the TAMB2.s operational state. The contact set is single pole, double throw, and changes state from what is screened below the terminals when the TAMB2 becomes active and returns when the unit becomes idle again. Contact Ratings: 0.6A @ 125V AC resistive 0.6A @ 110V DC
essary. 6. Adjust AMBIENT THRESHOLD until the STATUS LED starts flashing amber, then adjust ACTIVITY THRESHOLD until amber stops flashing. 9 Module Setup, cont. Normal Mode All sources are affected by the gain adjustment process. Background music source will need to be routed through the main mixer inputs, which will be affected by the gain adjustment process. Refer to page 12 for illustration. Start with all POTS turned fully clockwise (AUX IN is not used in this mode). 1. Set MODE Switch to "S
Installations requiring long-play background music are excellent applications for CD-R/RW discs containing a large number of MP3 files. Playback Modes Audio track selection can be configured in a variety of ways for playback. Tracks can be played back sequentially or randomly, manually or programmed (up to 32 tracks) from any one or up to five loaded discs. Random playback functions include random playback of tracks from one, all or programmed tracks from the loaded discs. Once all tracks are pl
It is an excellent choice for professional recordings, live performances, and other critical sound reinforcement applications. The HCU350 is a uni-directional microphone offering a minimum sensitivity at an angle of 180 degrees while reducing pickup of sounds from the rear. Its polar pattern focuses on the desired sound source while suppressing unwanted ambient noise and feedback, and ensures a clean separation between individual instruments. It incorporates a transformerless electronic circuit