Replace the oil as indicated in the Maintenance section of this Manual. • Use safety equipment including safety goggles or shield, ear protection, breathing or respirator mask and protective clothing. Wear goggles. Wear earmuffs. Wear a breathing or respirator mask. Never apply the outlet air of this compressor directly on to any part of a person’s body. Do not attempt to block the air outlet with your finger or any part of your body. The tool must be used only for its prescribed purpose. Any us

Drain cock 12. Air tank 13. Wheel (x 2) 14. Safety shield 15. Oil filling cap 16. Air filter assembly 17. Oil level glass 18. Oil drain plug (not shown) 12 14 16 13 17 9 5 1 3 2 7 10 8 11 15 6 4 9 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal inju

• Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devises Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Operation WARNING. Before connecting a tool to a power source, be sure th

A Copyright © 2005 Delta Machinery INSTRUCTION To learn more about DELTA MACHINERY visit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY GUIDELINES - DEFINITIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• Never use your hands to remove sawdust, chips or waste close by the saw blade. • Use only blades as recommended. • Rags, cloths, cord, string and the like should never be left around the work area. • Avoid cutting nails. Inspect the workpiece and remove all nails and other foreign objects before beginning sawing. • Support the work properly. • Never reach over the blade to remove waste or off cuts. • Do not attempt to free a jammed blade before first switching off the machine. • Do not slow or

Use blades of the same dimensions and weight, or the barrel will oscillate and vibrate causing poor planing action and possibly a machine breakdown. Tighten the clamping screws (8) carefully when attaching the blades to the planer. A loose clamping screw could be extremely dangerous. Regularly check to see they are tightened securely. NOTE. Your planing surface will end up rough and uneven unless the blades are set properly and securely. The blades must be mounted so that the cutting edge is abs

Single (full sequential actuation) firing To fire, grip tool firmly to maintain control, position the contact safety nose (1) of tool onto work surface, and squeeze trigger (4) to fire a fastener. Allow tool to recoil away from work surface as fastener is driven. This “full sequential actuation” method provides the most accurate fastener placement. Where to use framing nailer Framing nailer guns are used mainly in heavy construction applications. Some additional important safety applications are

Each is engineered and manufactured to the highest standards of quality. You will find your new Wood Turning Lathe a very useful tool. It will perform between centre turning and faceplate turning, and is especially suited to high speed sanding and polishing of finished work. This Wood Turning Lathe is a self-contained powertool not requiring the purchase of a seperater motor. MAIN FEATURES 1. HEAD 2. CABLE 3. DRIVE CENTER 4. TOOL RESTHOLDER 5. TOOL REST 6. REAR PART-BED RAIL 7. LIVE CEN

Use of the power tool for operations different from intended could result in a hazardous situation. Service • Have your power tool serviced by a qualified repair personnel using only identical replacement parts. • When operating a power tool outdoors, use an outdoor extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. This will ensure that the safety of the power tool is maintained. Additional safety instructions for engravers • Alwa

The pressure in the tank is controlled by the action of the pressure switch located under the pressure switch cover (2). When the set maximum pressure is reached the pressure switch activates and the motor is switched off. The pressure then decreases as the air is used by the connected tool until the set minimum pressure is reached after which the pressure switch causes the motor to switch on again. The operator of the compressor should be well aware that during use of the compressor the motor w