Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Never use your hands to remove sawdust, chips or waste close by the saw blade. • Use only blades as recommended. • Rags, cloths, cord, string and the like should never be left around the work area. • Avoid cutting nails. Inspect the workpiece and remove all nails and other foreign objects before beginning sawing. • Support the work properly. • Never reach over the blade to remove waste or off cuts. • Do not attempt to free a jammed blade before first switching off the machine. • Do not slow or stop a blade with a piece of wood. Let the blade come to rest naturally. • If you are interrupted when operating the saw, complete the process and switch off before looking up. • Periodically check that all nuts, bolts and other fixings are properly tightened. • Do not store materials or equipment above a machine in such a way that they could fall into it. • Ensure that your work is always on the table. Never attempt to cut anything that is not on the table. Wear goggles Wear earmuffs Wear a breathing mask 5 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Assembly The Band Saw is shipped partly disassembled and the saw table and rip fence guide have to be installed prior to use. 1. Remove the rip fence scale from the table. 2. Place the table onto the table trunnion. 3. Fix the table to the trunnion using the 4 hex head bolts and serrated lock washers. 4. Place the table insert into the hole in the centre of the table. 5. Replace the rip fence scale on the table. 6. Adjust the distance between the rip fence guides by raising the rip fence guide handle to unlock it and turning the handle. The distance between the guides needs to be long enough to enable the fence to fit over the table. 7. Position the fence on the table with the guides located in the channels either side of the table. 8. Slide the fence to the desired location and push the rip fence guide handle down to lock the fence in position. 9. If required, assemble the support stand and attach the band saw to this stand. 1 6 2 7 3 8 4 9 5 6 Know your product 1. Saw blade 2. Upper wheel housing 3. Saw band tensioning knob 4. Lower wheel housing 5. Saw band tensioning knob 6. Motor shaft (not shown) 7. Drive belt (not shown) 8. ON button 9. OFF button 10. Table insert 11. Rip fence 12. Rip fence scale 13. Rip fence guide 14. Rip fence guide handle 15. Table trunnion 16. Table trunnion bracket 17. Table tilt securing knob 18. 90. table tilt adjustable screw stop 19. Dust extraction port 20. Height adjustment knob 21. Blade support head 22. Table 23. Housing lock screws 7 3 9 21 1 11 22 13 2 10 23 8 12 14 4 5 15 18 16 17 20 Setting up Centring the table 1. Loosen the screws holding the table trunnion bracket 2. Move the table until the saw blade is positioned in the centre of the table insert 3. Tighten the bracket screws ensuring that the table does not move. Setting the table square with the saw blade 1. Loosen the table tilt-securing knob. 2. Adjust the hex headed screw stop on the underside of the table so that the table is at right angles to the saw blade when the screw rests on the lower wheel housing. Fixing 1. The Band saw should be stable. 2. Either secure it to the support stand provided or to the floor or to a bench or table. Note: Do not use the saw unless is is firmly fixed and stable. 3. There are four 9 mm fixing holes in the base of the saw. Rip fence The rip fence can be used either side of the blade. 1. Raise the rip fence guide handle to unlock it and turn the handle to increase the distance between the guides so that it can be lifted clear of the table. 2. Position the fence on the other side of the blade with the guides located in the channels either side of the table. 3. Slide the fence to the desired location and push the rip fence guide handle down to lock the fence in position. Dust collection 1. Connect dust extraction equipment to the 60 mm diam. dust extraction port. 2. The dust extraction equipment must provide for an airflow rate of at least 20 m/s. Caution. Wood dust and chips in a confined area can give rise to fire or an explosion. Guard against possible ignition sources. 8 Changing the saw band Warning. Ensure that the mains plug is removed from the power socket The saw is supplied with a general-purpose woodcutting blade. 1. To change the blade, first remove the rip fence scale. 2. Slacken the blade tension by rotating anti-clockwise the blade tensioning knob on the top of the upper wheel housing. 3. Open the doors to the upper and lower wheel housings. 4. Remove the old blade and fit the new blade. Tension the blade lightly by rotating clockwise the blade-tensioning knob on the top of the upper wheel housing. 5. Turn the upper wheel by hand to check that the blade is running...