Serial Decal QUESTIONS? If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE. The trained technicians on our customer hot line will provide immediate assistance, free of charge. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Ke

4. Do not use the hydrotherapy spa on carpet or other material that may be damaged by moisture. We recommend that you place the hydrotherapy spa on a water- and stain-resistant, non-slip surface with a floor drain for any water that may splash from the hydrotherapy spa. 5. Be sure that the location you choose is stable. It must be able to support the weight of the hydrotherapy spa when it is filled with water, plus the weight of the occupants. The hydrotherapy spa weighs approximately 2000 pound

Serial Number Decal Write the serial number in the space above for reference. QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are damaged or missing, PLEASE DO NOT CONTACT THE STORE. For assistance, contact our Customer Service Department CALL TOLL-FREE: 1-866-699-3756 Mon.–Fri. 6 a.m.–6 p.m. MST Sat. 8 a.m.–4 p.m. MST ON THE WEB: CAUTION Read all precautions and instructions in this manual before using this equipment

B. The underwater light can be used for night operation (see USING THE CONTROLS on page 12). The spa includes both red and blue covers for the light. C. The temperature probe monitors water temperature. D. The volcano jet provides a soothing foot massage. E. The whirlpool jet diverts the water flow three ways. By turning the outer ring completely counterclockwise, the water flow is diverted to the jets on seats 3, and the jets labeled D. By turning the outer ring to the middle position, the wate

Model No. 831.283100 USER'S MANUAL Serial No. Sedal Number Decal F----X_RCI_E; EQUIPMENT HELPLINEI 1-800-736-6879 SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 new products, prizes, fitness tips, and much morel TABLE OF CONTENTS IMPORTANT PRECAUTIONS ............................................................. 2 BEFORE YOU BEGIN ................................................................... 3 ASSEMBLY ........................................................................... 4 HOW TO

Write the serial number in the space above for reference. QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are damaged or missing, PLEASE DO NOT CONTACT THE STORE; please contact CustomerCare. IMPORTANT: You must note the product model number and serialnumber (see the drawing above) before contacting us: CALL TOLL-FREE: 1-866-699-3756 Mon.–Fri. 6 a.m.–6 p.m. MSTSat. 8 a.m.–4 p.m. MST ON THE WEB: CAUTION Read all precau

Two more jets are located on each of the bench seats, and they focus the water massage on your lower or middle back. The spa also features an ozone jet (C) which is part of the built-in ozone generator system. Ozone helps sanitize your spa with minimal chemical treatment. The suction vents (D) located near the floor of the spa brings the water into the pump in order to operate the system. The suction covers should always be in place over the suction vents. Never operate the spa without the sucti

See inset drawing B. When the Support Ball (58) is inflated, remove the inflation tube from the Support Ball and insert the ball plug through the mesh into the Support Ball. The head of the ball plug will hold the Support Ball in place. Note: The Support Ball (58) is not a toy. 8 9 13 12 9 A B 11 Mesh Pocket 58 58 Inflation Tube Ball Plug 58 10. Place the Spa Cover (11) over the Side Panels (1) and the Spa Jet Unit (13). Be sure that the Spa Cover is properly centered and that the corners of the

2 BEFORE YOU BEGIN ................................................................... 3 ASSEMBLY ........................................................................... 4 HOW TO OPERATE THE STEPPER ........................................................ 6 MAINTENANCE AND TROUBLESHOOTING .................................................. 7 CONDITIONING GUIDELINES ............................................................. 8 PART LIST .......................................................

STARTING THE SPA Once you have tested the GFCI, you should verify the water flow from the pumping unit. Set the air control on the console to the lowest setting (see USING THE CONSOLE below). The pumping unit will heat the water as it pumps. Cover the spa with the spa cover and liner. The spa cover must be tight. (See SECURING THE SPA COVER at the right.) The water will heat at about 3.0° F per hour with the cover on. If you are using the spa indoors and the room temperature is maintained at 70°