29 Allrepairs,adjustmentsandmaintenancenotdescribedintheOperator’sManualmustbeperformedbyqualifiedservicepersonnel. WARNING5152116172011131419212225263127185862424138353430363940372863646165754322423359575655545328915ClutchWasherKit60101263343 44454647484950 Ref. Part No. Description Ref. Part No. Description Ref. Part No. Description 1. 530071927 Kit- -- Trigger/Lockout 24. 530059677 Starter Hub- -- EPS 44. 530059999 Cover- -- Gearbox 2. 545011903 Cover- -- Handle 25. 530021180 Spring- -- EPS 4

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21 22 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802) CONTROL PANEL / DISCHARGE CHUTE 3 1 2 2 6 19 2 2 26 28 27 27 25 20 29 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 11 12 22 23 22 23 31 32 30 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802) CONTROL PANEL / DISCHARGE CHUTE KEY PART NO. NO. DESC

Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther. • To change the deflector position, loosen knob, move deflector to desired position and tighten knob securely. HIGH POSITION CHUTE DEFLECTOR LOW POSITION KNOB FIG. 11 9 OPERATION TO THROW SNOW (See Fig. 12) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Release the auger c

Failure to do so can cause the unit Pivot to malfunction and pose a risk of injury to the operator, points BEFORE EACH USE 1, Check engine oil level. 2. Check for loose fasteners, 3. Check controls to be sure they are functioning properly, LUBRICATION @ Keep your snow thrower well lubricated Engine (See "LUBRICATION CHART"). oil ® Auger grease fittings SNOW THROWER V-BELTS Always observe the safety rules when performing any maintenance. Check V-belts for deterioration and wear after every 50 hou

Please do not return unit to retailer. • 1-800-554-6723 Instruction Manual Manual de Instrucciones Manuel d'lnstructions BVM200VS ! IMPORTANT MANUAL -Do not throw away MANUAL IMPORTANTE -No Io descarte MANUEL IMPORTANT -A Conserver & WARNING: Read and follow alt Safety Rules and Operating Instructions before using this product. Failure to do so can resu_ in serious injury. ADVERTENOIA: Lea el manuat de instrucciones y siga todas tas advertencias e instrucciones de seguridad. Et no hacerlo puede

Contact at the upperportion of the tip of the guide bar can cause the chain to dig into the object and stop the chain for an instant. The result is a lightning fast, reverse reaction which kicks the guide bar up and back toward the operator. If the saw chain is pinched along the top of the guide bar, the guide bar can be driven rapidly back toward the operator. Either of these reactions can cause loss of saw control which can result in serious injury. __ 2. UNDERSTANDING REACTTVE FORCES Pinch-k

For removal of snow in normal con di tions, such as a paved driveway or side walk, place skid plates in the highest position (lowest scraper clear ance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven. NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal i

1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302) HANDLES KEY PART NO. NO. DESCRIPTION 10 10 10 1 2 3 4 5 5 6 7 9 8 01.12.001-E 1 180480 IMPELLER ROD ASSEMBLY 2 405740 TRACTION ROD ASSEMBLY 3 180445 SHIFTER ROD TOP 4 187716 SHIFTER ROD BOTTOM 5 180447 SPRING SLEEVE 6 178669 IMPELLER SPRING 7 180926 TRACT

MINIMUM WIRE GAUGE RECOMMENDATIONS Volts 25 ft. (7.67 m) 50 ft. (15.24 m) 100 ft. (30.48 m) 120 16 A.W.G.* 16 A.W.G.* 14 A.W.G.* PowerCordExtensionCord *American Wire Gauge 7 BEFORE STARTING SAW WARNING: Be sure to read the electrical safety information in the SAFETY RULES section of this manual before you begin. If you do not understand the electrical safety information do not attempt to use your unit. Seek help from someone that does understand the information or call the customer assistance h

Do not operate this saw unless you have specialized training and experience for dealing with kickback. Chain saws with significantly reduced kickback potential are available. POULAN PRO Shreveport, Louisiana 71139-9329 TABLE OF CONTENTS SPECIFICATIONS .....:.... ........... 2 WARNINGS & SAFETY INSTRUCTIONS .. 3 KNOW YOUR UNIT.................. ..... 6 PREPARING YOUR SAW FOR USE ........ 7 A. Getting Ready ......................... 7 B. Hardware Usage....................... 7 C. Attachi