It may take up to 30 seconds to fully extinguish. Additionally, the internal power transformer is provided with a thermostat which will interrupt power into the transformer if its temperature exceeds 125°C. This high temperature will seldom, if ever, be encountered unless the amplifier is subjected to abnormal conditions, such as operation into loads of less than 3 ohms at very high listening levels, etc. If the AC Fuse (4) has not failed, the Power LED is out, and the Thermal Protection LED (9)

No user serviceable parts inside. Refer servicing to qualified service personnel. EXPLANATION OF GRAPHIC SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. A The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor

To realize the full potential of your new receiver, please read these operating and installation instructions thoroughly before attempting to make any connections to it. The GFR-700HD is not only designed to reproduce the highest quality sound and picture but also to deliver the greatest possible value. It is our engineers’ passion for perfection that has enabled our components to be judged the equivalent of others costing two, three, or even five times as much. Our engineering team consistentl

SEE NEC SECTION 810-21 (1) DO NOT ATTEMPT SERVICING OF THIS UNIT YOURSELF. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-22 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 1. PRODUCT D

However, make sure that the cable ends are tinned before you make the cable connections to the banana plugs. Alternatively, you can use “crimped” pins or other lugs to ensure low contact resistance at the connection to the amplifier and loudspeakers. If you prefer to use other methods of connection, unscrew the insulated head of the binding post until the hole in the binding post stud is accessible. You can then insert the bare or tinned wire, or terminal pin, through the hole. You can also use

Be sure to clip wires well away from the amplifier to avoid this possibility Features and specifications subject to change without notice. ADCOM Car Audio is a registered trademark of ADCOM. All rights reserved. ©1994 ADCOM Inc. a@WMI[R,,S m h m y a l Congratulations! And thank you for choosing ADCOM Car Audio Amplifiers for your mobile sound system. Your ADCOM Car Audio Amplifier uses superior engineering principles and the highest quality components to provide a musical experience with cla

We know you are anxious to hear your new preamplifier in action, but please take a few minutes to read this owner’s manual before connecting the preamplifier to your system. It is particularly important that you connect your preamplifier to your amplifier while the amplifier and preamplifier are unplugged and your other equipment is turned off. This will protect your equipment from potential short circuits that may occur during installion. In addition, it is important that you allow for adequate

The unit may fall, causing serious injury to a child or adult, and serious damage to the unit Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the unit. Any mounting of the device should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. Read all the safety and operating instructions before connecting or using this unit. Retain this notice and the owner’s manual for future reference.

ADCOM GTP-860 OWNER’S MANUAL | 17 [32] Mute Button In all modes, this button is preprogrammed to mute outputs of device. Mute does not affect recordings made using the Tape outputs but will affect the signal going to the Preamp Outputs. When the unit is in mute mode, any adjustment of the Volume Control on the front panel [8] will release the muting, i.e. the original volume level will be resumed. [33] Dynamic Range Button In main mode, this button is preprogrammed to adjust dynamic range of Dol

As you’ve already seen, it’s preprogrammed to control ADCOM’s GTP-830 Preamp/Tuner and the GCD-700/750 CD players. In addition, it has seven “component memory banks” available so you can program the remote to learn commands for your DVD player, satellite box, laser disc player, VCR, etc. This lets you use one remote controller for your entire system. Using Preprogrammed Commands Using the remote controller’s preprogrammed commands is simple. For most GTP-830 functions (volume up/down, changing s