Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Each is engineered and manufactured to the highest standards of quality. You will find your new Wood Turning Lathe a very useful tool. It will perform between centre turning and faceplate turning, and is especially suited to high speed sanding and polishing of finished work. This Wood Turning Lathe is a self-contained powertool not requiring the purchase of a seperater motor. MAIN FEATURES 1. HEAD 2. CABLE 3. DRIVE CENTER 4. TOOL RESTHOLDER 5. TOOL REST 6. REAR PART-BED RAIL 7. LIVE CENTER 8. HAND WHEEL 9. TAIL STOCK 10. LOCKING HANDLE 11. FACE PLATE 12. WRENCH 13. SWITCH SAFETY RULES FOR ALL POWER TOOLS 1. READ AND BECOME FAMILIAR With the entire operating manual. 2. KEEP GUARDS AND COVER In place and in working order. 3. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operations is dusty. Everyday eyeglasses only have impact resistant lenses. They are not safely glasses. 4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 5. DON'T FORCE TOOL. It will do a better and safer job at the rate for which was designed. 6. AVOID ACCIDENTAL STARTING. Make sure switch is in "OFF" position before plugging in. 7. DISCONNECT TOOLS BEFORE SERVICING and when changing accessories such as spindle, centre, chuck etc. 8. DON'T OVER REACH. Keep your proper footing and balance at all times. For best footing wear rubber soled footwear. Keep floor clear of oil, scrap wood, etc. 9. WEAR PROPER APPRAEL. Loose clothing or jewelry may get caught in moving parts. Wear protective hair covering to contain long hair. 10. MAKE WORKSHOP KIDPROOF. Place a padlock on the switch when the machine is not in use and store the key in a safe location. 11. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 12. AVOID DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations. Keep your work area well illuminated. DO NOT USE in explosive atmosphere(around paint, flammable liquids, etc). 13. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area, especially while operation unit. 14. USE THE PROPER TOOL. Don't force tool or attachment to do a job for which it was not designed. 15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing ' accessories. 16. SECURE WORK. Use clamps or a vise to hold work, when practical. It's safer than using your hand and prevents round or irregularly shaped pieces from turning. 17. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function - check for alignment of moving parts, breakage of parts, mounting, any other conditions that may affect its operations. A guard or other part that is damaged should be properly repaired or replaced. 18. USE RECOMMENDED ACCESSORIES - Consult Owner's Manual. Use of improper accessories could be hazardous. 19. NEVER STAND ON TOOL. Injury could occur from a fall. 20. NEVER LEAVE TOOL RUNNING AND UNATTENDED. 21. ALWAYS REMOVE CORD PLUG from electrical outlet when adjusting, changing parts or working on tool. -2- BED RAIL CONNECTION As per instruction showed in Fig. 1,connecting the two part bed rails. Fig.1 TOOL REST HOLDER ASSEMBLY Put the tool rest holder properly on the bed rail, and fasten it with guide track plate by screw. See Fig.2 TOOL REST ASSEMBLY Insert the tool rest into the holderandlockitwith locking handle, See Fig.3 TAIL STOCK ASSEMBLY Assemble the tail stock as per Fig.4 INSTALLATION The wood lathe should be bolted to a solidly built work bench. Mouting holes are provided in the base at both the headstockand tailstock end of the lathe. Large flat was hers should be used between the bolt heads and the housing to fasten the wood lathe more -3- securely and prevent damage. Tighten snugly but do not overtighten. Fig.5 CHANGING SPEEDS 1. Turn the power off at the main switch. 2. Loosen motor mounting bolts under pulley cover. 3. Change belt to the desired pulley steps. 4. Lift belt tension lever to tighten belt. 5. Retighten. motor mounting bolts. CHANGING FACEPLATE AND DRIVE CENTRE The adjustment spanner has jaws which fit across flats on the headstock spindle. Locate the spanner across the flats and unsrew th faceplate or drive centre towards you. See Fig.7 MOVING TAILSTOCK AND TOOLREST The tailstock and toolrest are held to th'e bed with lock nuts underneath the bed rails. To move them to a new position, loosen the nut with the adjustment spanner, slide the tailstock or toolrest along the bed and retighten the nut, The toolrest is. held in place by the lockknob. See Fig.8 MOTOR An Induction type motor is provided with the lathe. The rearcoverofthe lathe has ventilation slots to provide additional air movement over the motor. ...