Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the indicated Screw (2), move the Reed Switch slightly, and then retighten the Screw. Reattach the hood and run the treadmill for a few minutes to check for a correct speed 2442 2 Top View 1/8” 23 a reading. 28 PROBLEM: The walking belt slows when walked on SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. b. If the walking belt is overt

Write the serial number in the space above for future reference. Model No. EPBE1506.0 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if a part is damaged or missing, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT DIRECTLY. CALL TOLL-FREE: 1-866-997-6999 Mon.–Fri., 6 a.m.–6 p.m. MST ON THE WEB: USER’S MANUAL CAUTION Rea

The walking belt will then slow to a stop. If desired, you can redefine to the program while using it. To change the speed or incline setting for the current segment, simply press the Speed or Incline buttons. When the current segment ends, the new setting will be saved in memory. To increase the length of the program, first wait until the program is completed. Then, press the Start button and program speed and incline settings for as many additional segments as desired. When you have added as m

The left display will show how long the program will last. A profile of the speed settings of the program will scroll across the matrix in the left display. 3 Press the Start button or the Speed increase button to start the program. A moment after the button is pressed, the treadmill will automatically adjust to the first speed and incline settings of the program. Hold the handrails and begin walking. Each preset program is divided into either 30 or 50 one-minute segments. One speed setting and

Have the second person hold the console assembly near the Uprights (84) as shown. Look under the console assembly and locate the Console Wire Harness (78). Cut the plastic ties securing the Upright Wire Harness (77) to the right Upright (84). Next, connect the Upright Wire Harness to the Console Wire Harness (78). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and then try again. IF THE CONNECTORS ARE NOT CONNECTED PROPE

CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Write the serial number in the space above for future reference. Serial Number Decal QUESTIONS? If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE. The trained technicians on our Customer Hot Line will provide imme

To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the treadmill until the catch is aligned with the latch pin. Slowly release the latch knob. Make sure that the catch is sec

Then, rotate the Shock Pin until it clips onto the Shock. With the help of a second person, lower the Frame (48) to the floor. 88 102 88 102 7 83 48 Bracket Bracket 7a 8 9 8. Remove the elastic band holding the Upright Wire Harness (75). Have two people hold the console assembly near the Left Upright (73) and the Right Upright (74). Connect the Upright Wire Harness to the console wire. Make sure to connect the connectors properly (see the inset drawing); the connectors should slide together easi

. If desired, adjust any of the values. Note: The last two values that you change will become your workout goals. Press the Start button to start the walking belt. A moment after the button is pressed, the walking belt will begin to move. Hold the handrails and begin walking. As you exercise, change the speed of the walking belt as desired by pressing the Speed increase and decrease buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if a button is held down, the sp

No other appliance should be on the same circuit. Do not use an extension cord. 11. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13. To purchase a surge suppressor, see your local EPIC dealer or call the toll-free telephone number on the front cover of this manual and order part number 146148, or see your local electronics store. 12. Failure to use a properly functioning surge suppressor could result in damage to the control system of the tread