If care label instructions are not available, use the following information as a guide. Dryer Rack Use the removable drying rack for boots, sneakers, fragile sweaters, nylon stockings – any items that might be damaged by tumbling. To use the rack: 1. Position L-shaped legs against round inset at back of dryer. 2. Rest the two front legs on either side of the lint screen. 3. Check to see that the rack is securely in position. 4. Place items to be dried on top of the rack. Allow space for air to c

NOTE: Save the shipping carton and packing materials for future storage or transport of the unit. Please check the contents of the hardware kit against the corresponding model check list, prior to installation of the unit. See lists below.(Fig.1) CAUTION! ! Your Room Air Conditioner was designed for easy installation in a single or double-hung window. NOTE: This unit is NOT designed for vertical (slider type) windows. NOTE: Surplus screw(s) for spare use. Installation instructions F. Your unit w

• A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired. • The power supply cord contains no use serviceable parts. Opening the tamper-resistant case voids all warranty and performance claims. INSTALLATION INSTRUCTIONS Unpack the Air Conditioner EXCESSIVE WEIGHT HAZARD Use two or more people to move and install air conditioner. Failure to do so can result in back or other injury. Remove packaging materials • Remo

In the FAN ONLY Mode, Room Temperature display range is from 0 (32 ) to 38 (99 ). Room Temperature below 32 ,the Temperature display L0. Room Temperature above 99 ,the Temperature display H1. NOTE: Temperature setting range is from 19 (66 ) to 31 (88 ). Fan Speed button Used to select fan speed in sequence auto, low, medium and high. Timer button Used to set or cancel timer operation. When the unit is in operation, you can set OFF TIMER.When the unit is off, you can set ON TIMER.Timer setting ra

—SAVE THESE INSTRUCTIONS — 4 WAC 5 6 8 USER MAN final 3/2/05 12:23 PM Page 7 INSTALLATION REQUIREMENTS • The portable air conditioner should be connected to a 115 V, 60 Hz, 15- or 20-amp fused 3-prong grounded outlet. • The use of a time-delay fuse or time-delay circuit breaker is recommended. • All wiring must comply with local and national electrical codes and be installed by a qualified electrician. If you have any questions, contact a qualified electrician. Electrical Requirements ELECTRIC S

Install two 3/8 long self-tapping screwsthrough these holes. " If the windowchannel frame isnot tall enough to use existing holes, drillnew holes off to theside of the existing holes toattach the unitbottom bar tothe support platform.The unitshould be firmly anchored to the window channel frame or support platform.(Seefig. D) 11.Slide inside window sashclosed. Be surevertical edge of inside windowsash is pressedfirmly against sideof unit cabinet. Cut remainingseal to widthof window opening. Remo

See (Fig. 2). NOTE: Screws must be reinstalled upon completion of the window installation to secure slide-out chassis. Please seek assistance for this procedure. Fig. 2 Fig. 1 Right side Philips screws Shutter Frame Right Shutter 1/4" screw For 10K to 12K models Channel 1/4" Screw Fig. 3 Fig. 4 Installation instructions 3. Assembly of the upper & lower channels to the cabinet A. " L" Shaped Top Channel: Stick the double adhering seal to the " L" shaped top channel, and then Install the "L" shape

If the leveling screws are distanced too far away from the wall to provide stability, it may be necessary for you to fill this area with a solid piece of wood. See (Fig. 8). Fig. 5 Bracket Assembly Bracket Bolts Leveling Screw V-slot 90 Angle Support Brackets (TOP VIEW) Center Window sill V-slot (2) 3/4" screws per bracket Bracket Assembly Leveling Screw Outer Wall Construction 3/16" Maximum B. Measure the inside window sill width and find the center as shown in (Fig. 6). Align the V-slot in eac

When using THERMOSTAT, be sure to allow three minutes before changing temperature. Adjusting too quickly may cause an overload resulting in a blown fuse. ! CAUTION ! MODE Fig.9 The mode knob controls fan speeds and cooling speeds. To set desired cooling temperature, simply rotate the mode knob dial to the appropriate setting. See Fig. 9. LOW FAN will circulate the air at a minimum speed without cooling. HIGH FAN will circulate the air at a maximum speed without cooling. LOW COOL provides cooling

In the FAN ONLY Mode, Room Temperature display range is from 0°C (32°F) to 38°C (99°F). Room Temperature below 32°F, the Temperature display L0. Room Temperature above 99°F, the Temperature display H1. If the OFF TIMER is set, the time LED displays the remaining time to turn off the unit for only 12 seconds, then LED shifts to display set temperature. If you press TIMER button within the 12 seconds, OFF TIMER will be cancelled. If the ON TIMER is set, the timer LED displays the remaining time to