Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Use of the power tool for operations different from intended could result in a hazardous situation. Service • Have your power tool serviced by a qualified repair personnel using only identical replacement parts. • When operating a power tool outdoors, use an outdoor extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. This will ensure that the safety of the power tool is maintained. Additional safety instructions for engravers • Always wear eye, ear and breathing protection • Do not apply too much pressure when engraving WARNING. The use of an accessory or attachment, other than those recommended in this Instruction Manual, may present a risk of personal injury. To use this tool properly, you must observe the safety regulations, the assembly instructions and the operating instructions to be found in this Manual. All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards. Children and infirmed people must not use this tool. Children should be supervised at all times if they are in the area in which the tool is being used. It is also imperative that you observe the accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design: • Damage to the lungs if an effective dust mask is not worn. • Damage to hearing if effective earmuffs are not worn. • Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devices Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Installing an engraver tip WARNING. Disconnect the engraver from the power supply before making any adjustments or maintenance procedures. 1. Loosen the tip release screw (4) by turning it anti- clockwise with a flat head screwdriver. 2. To fit the new engraving tip (2), insert the tip through the centre of the hole of the engraver, ensuring the tip fully enters the housing. A new tip should protrude from the end of the housing by approximately 8.5mm. 3. Tighten the tip release screw (4) fully by rotating in a clockwise direction. Operation WARNING. Always wear safety glasses when using this tool. The GMC engraver can be used to permanently mark metal, glass, plastic, wood, ceramics and much more. 1. Before using the engraver you must ensure there is an engraving tip installed. 2. Connect the engraver plug to the power supply and while holding the engraver firmly, push up on the on/off switch (1) with your thumb. NOTE. To turn the tool on, press the small On/Off Switch (1) upwards to the (I) position. To turn the tool off, push the on/off Switch (1) down to the (O) position. 3. Hold the engraver at an angle, like you would hold a pen. Do not press down hard while engraving, use light pressure while guiding the point over the work to be completed. Adjusting the depth of engraving 1. The stroke adjustment dial (3) located on the side of the engraver controls the stroke length and therefore the depth of engraving. 2. For a fine mark turn the stroke adjustment dial (3) anti-clockwise to position ‘1’. 3. For a deeper, thicker mark turn the stroke adjustment dial (3) clockwise to position ‘5’ NOTE. It is recommended that you practice on scrap material before you start. Maintenance WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. 1. Use a soft brush to remove any accumulated dust. Wear safety glasses to protect your eyes whilst cleaning. 2. If the body of the tool needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but never alcohol, petrol or other harsh cleaning agents. 3. Never use caustic agents to clean plastic parts. CAUTION. Water must never come into contact with the tool. General inspection Regularly check that all the fixing screws are tight. They may vibrate loose over time. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. Please refer to your warranty card, which is separate to these instructions. Full 2-Year Warranty This product is warranted for a 2-year period for home domestic use from the date of the original purchase. If found to be defective in materials or workmanship,...