5 (540 RPM) Cat. 4 or 5 (1000 RPM) Wing Driveline ASAE Cat. 5 Slip Clutches (2) 4 Friction Plates Blade Tip Speed 16,289 FPM/540 RPM; 16,000 FPM/1000 RPM Blades 1/2 x 4 inches - Uplift with 6 inch Overlap Type Hitch Self Leveling with Perma Level Hitch® or 2 5/16 inch Ball Hitch or Swivel Clevis Hitch Wing Flex 87° Up to 22° Down Tires Laminated, Pneumatic or Aircraft Axles Greaseable with bushings Wheel Shock Protection Independent Springs/Each Axle Deflectors Standard Front Belting a

The open-center system constantly pumps oil through the hydraulic cylinder operating valves and returns the oil to the reservoir. The closed-center system does not pump oil until there is a demand for oil from one of the hydraulic cylinders. In this case, CLOSED-CENTER means that when the operating valves which control the hydraulic cylinders are in the neutral position, there is no flow of oil through the valves. As long as the engine and pump are running, a constant stand-by oil pressure of ap

pressure & 11 GPM pump capacity Bush Hog Quick Attach Buckets Available in 60, 72 and 80 inch widths Bush Hog Quick Attach Heavy Duty Buckets Available in 60, 72 and 84 inch widths Options Forklift Attachment (42 inch tines), Round Bale Spear, Grapple Fork, Bucket Tine Teeth, Bolt-On Digging Teeth, Side Cutting Edges, Spill Guard Attachment, Hydraulic Self-Leveling, and Grill Guards Warranty 1 year limited warranty FEATURES Available in major tractor colors SPECIFICATIONS SUBJECT TO CHANG

nches 650 lbs double roller models PVB-602 60 inches 640 lbs PVB-662 66 inches 680 lbs PVB-722 72 inches 720 lbs PVB-842 84 inches 790 lbs PVs-602 60 inches 640 lbs PVs-662 66 inches 680 lbs PVs-722 72 inches 720 lbs PVs-842 84 inches 790 lbs Maximum Tractor HP 60 PTO (all models) Type Hitch Category I (all models) Warranty 1 year limited warranty Single or Double Rear Roller, Bar (reversible) or Spike Shanks, 1 1/4 Inch Spikes on Rollers SPECIFICATIONS SUBJECT TO CHAN

2. Fit the two spacers and the bracket over the outer tube and loosely install the four socket-head screws. 3. Tighten the four socket-head cap screws to secure the cutting attachment shield. 4-6 mm Remove air cleaner coverThrottle lever free play Lock Nut Adjust as required to obtail 4-6 mm free play Cable Adjuster Sub-Shield (when trimmer head is in use) Outer Tube Socket-Head Cap Screws RetainingNut Mounting Plate Spacer Spacer Bracket Cutting Attachment Shield w/subshield Cutting attachment

Restart. Troubleshooting Guide (continued) LOW POWER OUTPUT What To Check Is the engine overheating? Possible Cause Operator is overworking the unit. Carburetor mixture is too lean. Improper fuel ratio. Fan, fan cover, cylinder fins dirty or damaged. Carbon deposits on the piston or in the muffler. Clogged air cleaner element. Loose or damaged spark plug. Air leakage or clogged fuel line. Water in the fuel. Piston seizure. Faulty carburetor and/or diaphragm. Remedy Use a lower throttle setting.

1. Wear protective equipment such as , but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equipment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks, or other mechanical devices. 3. Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly to trip. 4. Arrange parts to be assembled neatly

ansmission Chain Drive (#60) Chain Drive (#60) Depth of Cut 6 inches 6 inches Driveline Slip Clutch Standard Slip Clutch Standard Approximate Weight 308 lbs 335 lbs Warranty 1 year limited warranty FEATURES 1 • Available in major tractor colors SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

If driveline has less than minimum overlap, DO NOT USE. Contact authorized Bush Hog dealer. NOTE If driveline is correct length, omit the fol- lowing steps “G” through “J” and proceed to step “K”. Figure 2-1Figure 2-2MinimumOverlap 7 G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-3 H. Usingcut off section of shield as a guide, cutshaft the same amount. (Figure 2-4) Figure 2-4 I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of dri

I, Cat. II Standard & QH 3 Point Cat. I, Cat. II Standard & QH 3 Point Cat. I, Cat. II Standard & and QH Deck Thickness 10 gauge 10 gauge 10 gauge Sidebands 1/4 x 13 inches 1/4 x 13 inches 1/4 x 13 inches Driveshaft ASAE Category 4 ASAE Category 4 ASAE Category 4 Gearbox 130 HP 130 HP 130 HP Tractor PTO Speed 540 RPM 540 RPM 540/1000 RPM Driveline Protection Slip Clutch Standard Slip Clutch Standard Slip Clutch Standard Blade Holder(s) Round Round Round Blades 1/2 x 4 inch uplift 1/2 x 4