Refer to Figure 2-6. Correct Angle 19376 Incorrect Angle 19377 Bucket Digging Angle Figure 2-5 When loading trucks, curling the bucket close to the dipper stick will prevent undue spillage when the bucket is raised so that it can be dumped in the truck bed. To obtain a level bottom, set the bucket teeth at a slight angle. Keep this angle as you drag the bucket with the dipper stick by gradually uncurling the bucket. Intermittently pull the boom lever at the same time to maintain a level bottom.

180.019.116.1 COMER PRESSURE PLATE 9. 165.000.548 COMER BOLT WITH NUT M10X100 10. 165.000.589 COMER TAPERED PIN SET 1 3/4 10/23/12 RC5515, RCM5515, RC6515 & RCM6515 Rotary Cutters 318-721P 125 Table of Contents Part Number Index Land Pride Section 5: Drivelines (540 RPM) Driveline Slip Clutch (146.284.020.1) Comer Applies to RC5515, RC6515 126 RC5515, RCM5515, RC6515 & RCM6515 Rotary Cutters 318-721P 10/23/12 Table of Contents Part Number Index Section 5: Drivelines (540 RPM) Land Pride Drivelin

Part No. Part Description Comments Revision dwg15325 Drawing Image Number 315.010 COSMO GEAR BOX ASSY 1. 304.003 COSMO OUTPUT COWLING 2. 314.002 COSMO UPPER SHELL 3. 310.001 COSMO BALL BEARING OUTPUT TOP 4. 316.003 COSMO PINION GEAR 5. 310.002 COSMO BALL BEARING IN/OUTPUT 6. 329.011 COSMO SPACER INPUT SHAFT 7. 323.008 COSMO INPUT SHAFT 8. 326.003 COSMO SPLINE KEY 9. 309.001 COSMO INPUT SHAFT OILSEAL 10. 313.011 COSMO INTERNAL RETAINER RING 11. 323.009 COSMO OUTPUT SHAFT 12. 305.002 COSMO SPLIT P

803-014C NUT HEX 3/8-16 PLT 31. 803-020C NUT HEX 1/2-13 PLT 32. 803-084C NUT HEX NYLOCK 5/16-18 PLT 33. 803-088C NUT HEX LOCK 1/4-20 FLG 34. 803-209C NUT FLANGE LOCK 3/8-16 PLT 35. 804-004C WASHER INTERNAL STAR #10 PLT 36. 804-007C WASHER FLAT 1/4 SAE PLT 37. 804-009C WASHER LOCK SPRING 5/16 PLT 38. 804-012C WASHER FLAT 3/8 SAE PLT 39. 804-013C WASHER LOCK SPRING 3/8 PLT 40. 804-015C WASHER LOCK SPRING 1/2 PLT 41. 804-036C WASHER FLAT 5/16 SAE PLT 42. 804-056C WASHER WAVE SPRING 5/16 43. 817-033

318-000M h When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these instructions for future reference. Your Blade Bolt Kit is exclusively designed for your Land Pride Rotary Cutter. Please read these installation instructions and your Rotary Cutter Operator’s Manua

The muf fler cover is attached to the engine cover at the top and front by tabs. To remove push inward at arrow area while pulling outward. See insert image. 3. With a Phillips type screwdriver remove the 5 screws holding the spark arrester screen and cover to the muffler. 4. Remove the screen and clean it with a stiff bristle brush. muffler. 6. Inspect the cylinder exhaust port for any carbon buildup. 7. Gently tap the muffler on a wood sur face to dislodge any loose carbon. 8. Reassemble the s

Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended). * meets or exceeds these specifications and is recommended for all Shindaiwa products. Specifications are subject to change without notice. This unit comes fully assembled with the exception of the handlebar, cutting attachment shield and cutting attachment. IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operato

Y If the spark plug is fouled or soaked with fuel, clean the plug as necessary. Stopping the Engine Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position. Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate at engin

325-175D SHAFT, 56 AERATOR ROTOR 4. 325-161D PIPE SCH 80 1X2 5/16L BLACK 5. 800-080C GREASE ZERK 1/4-28 THD FORMING 6. 802-167C HHCS 1/4-20X1 1/2 GR5 7. 803-255C NUT HEX NYLOCK 1/4-20 8. 804-029C WASHER FLAT 1 SAE 9. 820-420C 1/2" HARDENED AERATOR SPOON CA0540 40 Total, CA0548 48 Total & CA0556 56 Total 01/20/10 CA0540, CA0548 & CA0556 Core Aerators 325-108P 11 Table of Contents Part Number Index Land Pride Section 4: Labels CA05 SERIES Label Placement Applies to CA0540, CA0548, CA0556 12 CA0540

Specifications & Capacities Rotary Tillers RTA20 Series RTA2064 RTA2072 Recommended Tractor PTO HP 23-50 Horsepower (50 hp maximum) Weight 689 lbs. 734 lbs. Tilling Width 64" 72" Overall Width 70 13/16" 77 7/8" 3-Point Hitch Type Category I, Adjustable Lower Hitch Clevis with Plated Pins Fits land Pride Quick-Hitch Sideshift Capabilities 14" | 18" Note: Limited sideshift capabilities with Land Pride Quick-Hitch Number of Flanges 8 9 Number of Tines per Flange 6 Tine Construct