Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended). * meets or exceeds these specifications and is recommended for all Shindaiwa products. Specifications are subject to change without notice. This unit comes fully assembled with the exception of the handlebar, cutting attachment shield and cutting attachment. IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation. Prior to Assembly Before assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage. n Engine/Outer tube assembly n Handlebar and Throttle assembly n Cutting attachment shield n Cutting attachment n Kit containing cutting attachment shield mounting bracket and hardware, this owner’s/operator’s manual and tool kit for routine maintenance. Tool kits vary by model and may include a hex wrench, and a spark plug/screwdriver combination wrench. Assembly Cutting Attachment Shield Cutting Attachment Shield Bracket Socket- Head Cap Screw Outer Tube Shim Clamp Screw Shim Line Cutter Cutting Attachment Mounting Plate Retaining Nut Cutting Attachment Shield Sub-shield with Line Cutter Figure 5A Figure 5 Install the Cutting Attachment Shield C242 Cutting Attachment Shield 1. Insert the cutting attachment shield between the outer tube and the cutting attachment mounting plate. See Figure 5. 2. Fit the two shims and the bracket over the outer tube and loosely install the four socket-head screws. See Figure 5. 3. Tighten the four socket-head cap screws to secure the cutting attachment shield. 4. Re-tighten clamp screw and retaining nut. WARNING! NEVER operate the unit without the cutting attachment shield installed and tightly secured! NOTE: It may be necessary to loosen the retaining nut and clamp screw to adjust cutting attachment shield mounting plate. Hook Receiver Sub-Shield C242 (when trimmer head is in use) 1. Attach the shield extension to the cutting attachment shield. See figure 6. Hook Sub-shield Figure 6 WARNING! NEVER use this machine without sub-shield when using a trimmer head. CAUTION! Make sure the sub-shield is completely hooked at the hook receiver. CAUTION! Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket-head cap screws. Assembly (Continued) Handle Bar C242 Install the handlebar: 1. Use the 4 mm hex wrench to remove the lower cap retaining screws from the handlebar bracket. Remove the cap from the bracket. See Figure 7. 2. Position the handle on the outer tube forward of Handle Positioning Label as shown in Figure 7. Reassemble the lower cap to the handlebar bracket in the reverse order of disassembly. 3. Locate the handle in the best position for operator comfort. 4. Firmly tighten both lower cap retaining screws. 5. Install the protector sleeve on the outer tube. See Figure 7. Ignition Switch Handle Positioning Label POSITION HANDLEFORWARD OF THIS LINE Hanger Shoulder Strap Throttle Trigger Protector Sleeve Handlebar Outer Tube Mounting Bracket Socket-Head Cap Screw C242 Figure 7 Adjustments Adjust Throttle Lever Free Play 3. Turn the cable adjuster in or out as required to obtain proper free play 3/16-1/4 inch (4-6 mm). See Figure 10. 4. Tighten the locknut. The throttle lever free play should be approximately 3/16-1/4 inch (4-6 mm). See Figure 8. Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow. Lock Nut Cable Adjuster Figure 9 3/16-1/4 inch (4-6 mm) Throttle Free Play 1. Loosen the air cleaner cover knob and remove the air cleaner cover. See Figure 9. 2. Loosen the lock nut on the cable adjuster. See Figure 10. Figure 10 Figure 8 5. Reinstall the air cleaner cover. Installing a Trimmer Head NOTE: The C242 is shipped with Holder A, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE! 1. With the gear case output shaft facing up, rotate the gearshaft and holder A until the hole in holder A aligns with the matching hole in the gear case flange, and then lock the holder to the gear by inserting the long end of the hex wrench through both holes. See Figure 11A. 2. Using the combination spark plug/ screwdriver wrench, remove the shaft bolt and bolt guard. See Figure 11A. NOTE: Make sure holder B is installed on the gear- case with the splined hole engaging the gear- case shaft. 3. Using the hex wrench to secure Holder A , install and hand-tighten the trimmer head (counter-clockwise to install). See Figure 11B. 5. Remove the hex wrench from the gear case and holder. Hand-tighten Trimmer Head (counter- clockwise to install) Shaft Bolt (not used) Gear Case Shaft Bolt Guard (not used) Holder B Holder A Hex Wrench Figure 11B Figure 11A The C242 should now be completely assembled to oper...
Эта инструкция также подходит к моделям:Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)