This is available through a receptacle in the factory installed junction box. The junction box is located in the controls compartment of the fireplace. A variable speed control is provided with the blower system to provide quiet forced air flow at the desired speeds. A temperature sensor switch, which automatically turns the blower ON/OFF, is also provided with this kit. 2.0 CHECK CONTENTS OF SHIPPING CARTON Compare CONTENTS OF CARTON in Figure 1 with the actual parts received. If any parts are

. . . . 10 H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10 I. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11 J. Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . . 12 K. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 L. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 13 3 Maintenance and Service A. Maintenance Tasks-Homeowner . . . . . . . . . . . . .

• Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation. DO NOTDISCARD Tested and Listed by Beaverton Oregon USA OMNI-Test Laboratories, Inc. C US OWNER’S MANUAL Installation and Operation Model: 830-0381 3100-I ACT WOOD INSERT Advanced Combustion Technology (ACT) DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible f

Adjust or replace inlet regulatorif necessary. C. Valve. Replace valve and thermocouple interrupter. 7. 3 short beeps while the motor turns. A. Batteries are low. Replace batteries - quality alkaline recommended. WARNING: Creating anelectrical short between the batteries/battery box and metal parts of theappliance may render the receiver inoperable. 8. Pilot flame lights but there isno main gas flow. A. Manual override know (ifequipped) is in MANposition. Turn Manual override know to ON position

WARNING • Do NOT store flammable materials in the appliance’s vicinity. • Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. • Keep all such liquids well away from the heater while it is in use. • Combustible materials may ignite. Fire Risk. WARNING • High ash fuels, or lack of maintenance, can cause the firepot to fill with ash and clinker. If the firepot fills to the top, immediately shut down the unit and clea

Slide assembled trim over panel set. See Figure 12B. Figure 12A Figure 12B Adjust position by sliding left or right after top is in place. Install sides and push out to maximum distance of slot. Panel brackets DOOR HANDLE ASSEMBLY 1. Install washer on door handle shaft. . Slide door handle through door. 3. Install second washer(s) as shown. 4. Install key in groove. 5. Align groove in latch cam with key; slide latch cam over shaft. 6. Install locknut. Caution! Do not overtighten locknut. Door ha

D. Mantel and Wall Projections Combustible Mantel Legs or Wall Projections WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Combustible Mantels Note: All measurements in inches. 18 14-1/4 10-1/2 6-3/4 3 7-3/4 8-7/8 10 11-1/8 12-1/4 MEASUREMENTS FROM TOP EDGE OF HOOD Figure 5.4 Combustible Mantel Leg or Wall Project

Do not cut corners. Serious complications and possible safety risks may occur. Always use a certified installer. This installation is not recommended FIREPLACE INSERT INSTALLATION CONTINUED…… The MagnuM Countryside Model 3502 Fireplace Insert requires a fireplace shroud for proper installation. The shroud is designed to slip over the stove-top between the front and back hopper lids. Shrouds can be customized for particular installations (custom order). 1) Position unit so that the shroud can be

(102 mm) beyond the fireplace. • See Figure 7.1. Outer Shell of Fireplace Firebox Maintain air clearance to combustibles. Repack Insulation Knockout Gas Line Gas Line Refractory Seal with fireplace mortar or high temp noncombustible sealant 4 in. Combustible Materials 1-1/2 in. (38 mm) air space Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side. B. Junction Box Installation Your appliance is supplied with a Junction Box Kit. We recommend

• Pre-warm the flue to establish a draft to help reduce smoke spillage during start-up. Hold a rolled up piece of burning newspaper under the flue damper for a few moments. • Light the crumpled paper to ignite the kindling. • Add small pieces of wood until a hot bed of embers has been established. • Add a minimum of three average size pieces of split firewood, placed to allow combustion air and flames between them. CAUTION! Odors and vapors released during initial operation may be irritating to