NOTE: On DCR models – if your tractor has a Category 0 3 point hitch (20” drawbar spacing), then the lift arm pins must be installed to the inside of the frame. If the tractor has a Category I 3 point hitch (26” drawbar spacing), then the pull pins must be installed on the outside of the frame. c. Attach the mast of the main frame to the tractor by installing the tractor center (or top) link with a top link pin (not furnished). NOTE: Use stabilizer bars, adjustable sway chains, or sway blocks on

Stop loader gradually when lowering or lifting loads. 8 SAFETY INSTRUCTIONS (continued) OPERATIONAL SAFETY (continued) Allow for additional length of loader and bale on tractor while turning. Never allow anyone to walk or work under a raised loader. Do not use loader for a work platform. Do not lift or carry anyone on loader or in bucket or on attachment. Set both front and rear tractor wheels wide for increased stability. Be sure that people, livestock, or pets are not standing near the machine

DCR-4 LRHD-7 (Rakes shown with optional gauge wheels) 3 PT. LANDSCAPE RAKE Safety Instructions Assembly & Mounting Tractor Preparation Maintenance Operating Instructions Repair Parts CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE 1. Select an area for assembly that is clean and free of any 6. After completing assembly, thoroughly inspect the debris which might cause persons working on the machine to be sure that all nut

Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit is in a safe condition. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate the skin. Openings in the skin and minor cuts are susceptible t

Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. • Service work does not require going underneath. • Read Manual for service instructions or have service performed by a qualified dealer. WARNING! Keep all persons away from operator control area while performing adjustments, service, or maintenance. Before dismounting power unit or performing any service or

If its ability to do a job, or to do so safely, is in question – DON’T TRY IT. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, ma

Be sure tractor is properly counter-balanced with weights before attempting to lift any load with the Bale Spear attachment. If you are handling bales with both the front end loader and the 3 pt. hitch on the tractor, always load the 3 pt. attachment first and unload last. The bale spear is to be used only for handling hay bales. Do not use for digging rocks, pulling out fence, or as a craning device with a chain over the spear. LARGE ROUND BALES: Using the bucket tilt cylinders, adjust the angl

1 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . Worksaver warrants to the original purchaser of any new 3 Pt. Landscape Rake, that the equipment be free from defects in material and workmanship for a period of six (6) months for non-commercial, state, and municipalities. Use sixty (60) days for commercial use from date of retail sale. Replacement or repair parts installed in the equipment covered by this warranty are warranted for ninety (90) days from the date of purcha

Check all frame mounting bolts to make sure they are tight. Place the main frame of the bale spear attachement on the front of the loader. On the 300, 400, and 500 series loaders, install the lock pins. On the 600 and 700 series loaders, make sure the latch bars are properly engaged. Raise the loader and main frame slightly so that the bottom of the main frame is about one or two inches off the ground. Engage tractor parking brake and shut off the engine. Place some solid blocking under the main

Keep load low. WARNING! For multiple spear models, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. TRANSPORTING —————————————————— CAUTION! When traveling on public roads, whether at night or during the day, use accessory light and devices for adequate warnings to operators of other vehicles. Comply with all federal, state and local laws. Carry load low. Check visibil