Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
NOTE: On DCR models – if your tractor has a Category 0 3 point hitch (20” drawbar spacing), then the lift arm pins must be installed to the inside of the frame. If the tractor has a Category I 3 point hitch (26” drawbar spacing), then the pull pins must be installed on the outside of the frame. c. Attach the mast of the main frame to the tractor by installing the tractor center (or top) link with a top link pin (not furnished). NOTE: Use stabilizer bars, adjustable sway chains, or sway blocks on your tractor lift arms to keep the landscape rake from swinging side to side. An anti-sway device is a must if operating the landscape rake in a reverse (pushing) position. 3. Install the rake tine bar assembly to the mounting frame and retain with 1” bolt, flat washer and locknut. The locknut should be just loose enough for the rake assembly to pivot. 7 INSTRUCTIONS (continued) ASSEMBLY (continued) —————————————————— FOR MODEL LRHD RAKES Place jack stands or suitable blocking under tinebar so center pivot bolt and 3 pt. mount can be installed. Place 3 pt. frame assembly on top of the tinebar and align 1 inch pivot hole with center hole on tine bar. Install 1 inch pivot bolt and flat washer. Tighten bolt so 3 pt. mount will swing but without excessive looseness. Place 3 pt. frame in desired position and install angle shift pin. Place parking stand in position to support landscape rake. GAUGE WHEEL INSTALLATION —————————————————— SINGLE WHEEL PACKAGE (DCR Models Only) Refer to the parts illustration and assemble the wheel package to the center of the rake frame weldment using (4) bolts, nuts and washers as shown. Grease the wheel upon initial assembly. DUAL WHEEL PACKAGE (Recommended for rakes above 6’ in width and all MCR and LRHD Series rakes) Refer to the parts illustration and install the gauge wheel arms approximately one foot in from each end of the rake using longer carriage bolts provided. Grease the wheels upon initial assembly. Set up gauge wheels to the desired height using the spacers and washers provided. Lock caster wheel spindle in place with linch pin. CONNECTING LANDSCAPE RAKE TO TRACTOR —————————————————— ALL MODELS The landscape rake is compatible with Category 1, 3 point tractors equipped with side swing-type lower lift arms and some Category 0 tractors. 1. To avoid interference with the landscape rake, adjust tractor drawbar to the shortest and highest position. 2. Attach the tractor’s lower lift arms to the landscape rake and secure in place with lock pin. For Category 0 Hitch application, order optional pull pin kit part #590331 (one pair); replace the Category 1 pins with the Category 0 pins. Make sure the Category 0 pins are on the inside. 3. Tractor must be equipped with stabilizer bars, adjustable sway chains, or sway blocks to keep the implement from swinging side to side. 4. Attach the tractor’s top link to the top of the landscape rake’s mast and secure with the top link pin and retaining pin supplied with the top link. IMPORTANT ¦ ¦¦ Make sure rake is at least 6” (15 cm) from tractor tires throughout complete range of 3 point hitch operation. Level the A-frame and tinebar with 3 point connecting links and top link. Adjusting the top link length will change the fore and aft pitch of the teeth. Lengthening the top link will cause the teeth to contact the ground with a sharper pitch and be more aggressive. You may need to adjust the optional gauge wheels after adjusting pitch to maintain the desired working depth. FOR MODEL LRHD RAKES ONLY For Category 1 Quick Hitch application, order optional bushing kit part #862500 (one pair); place bushing over draw pin and fasten with roll pin. For Quick Hitch application, the top center hitch hook will seat into welded 11/4” diameter pin. This pin does not interfere when unit is used with a standard 3 point hitch. 8 OPERATION OPERATION —————————————————— The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 3 through page 6. The landscape rake is designed for a wide range of applications: loosening, leveling, and clearing soil or debris. The rake may be angled to windrow material to the side for removal. WARNING! Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times. WARNING! When using the rake in a reverse position, use extra care – DO NOT RAM RAKE into di...
Эта инструкция также подходит к моделям:Погрузчики - DCR-4 (231.32 kb)
Погрузчики - LRHD-6 (231.32 kb)
Погрузчики - LRHD-7 (231.32 kb)
Погрузчики - LRHD-8 (231.32 kb)