This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. Copyright Notes This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyrigh

Fast forwards the chapter/track or selects the next radio frequency. Fast reverses the chapter/track or selects the previous frequency. Press once to MUTE audio, press again to return audio, an icon indicator will flash on the TFT monitor. Press POWER momentarily to turn the unit on. Press and hold POWER for more than seconds to turn the unit off. Note: EJECT will still function even if POWER is off. Rotate VOLUME rotary knob Q or • for desired VOLUME level, press once to access the AUDIO SETUP

(consult a qualified technician for instructions) •Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Remove trim ring by pulling up gently in the center. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into dash opening, bending t

Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press and hold to turn the unit off. Press MODE to select between AM/FM, CD player, auxiliary input and USB. Modes of operation are indicated in the display. Note: CD mode will not appear unless a CD is inserted. Insert 3.5 mm plug to connect your portable audio

5. Fit the speaker to the hole cut-out. Mount the speaker using the supplied screws. If the speaker grill is to be used, insert 4 screws into the grill holes and then mount the speaker. DS SERIES INSTALLATION Specifications MOUNTING HEIGHTTWEETER PROTRUSIONTOP-MOUNTING DEPTHBOTTOM-MOUNTING DEPTHCUT-OUT DIAMETER The diagram featured above is to be used in conjunction with the specifications matrix guide below: DS42 .38" 2.25" .25" 2.00" 3.63" 86 85Hz-20kHz 50 100 DS52 .44" 3.06" .31" 2.75" 4.56"

TYPICAL MOUNTING METHOD XPE SERIES INSTALLATION Connection Descriptions NOTE Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire fr

Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove trim ring from unit, • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wirin

Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • DIN mounting procedure: Install mounting sleeve into radio opening, bending tabs to secure. • 2-Shaft m

Then line up the dock connector and insert the iPod device into the dock. Release the side supports to secure the device. XML8100 OPERATION Operation of iPod Insert the iPod device into the XML8100's Dock, following the instructions on pages 11 and 12. The iPod device can be controlled directly from the iPod device's interface, or controlled using the inside panel buttons shown below: Press ll to skip to the beginning of the next song. Press nn to return to the beginning of the current song. Pre

Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs