Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
(consult a qualified technician for instructions) •Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Remove trim ring by pulling up gently in the center. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into dash opening, bending tabs to secure. • Connect wiring harness and antenna. (consult a qualified technician if you are unsure) • Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). •Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. XD5210 INSTALLATION Installation 3 TYPICAL MOUNTING METHOD XD5210 INSTALLATION Antenna Connector RCA Cable (sold separately) Remote Turn-On Connect to amplifier or power antenna. Insulate wire if not used. BLUE Rear Preamp Output Connect to amplifier RCA Input GRAY Ground Connect to vehicle chassis ground. BLACK .5 AMP AGC Fuse Accessory Connect to existing ignition circuit or switched 12 volt source. RED 5 AMP AGC Fuse Memory Connect to battery circuit or constant 12 volt source. YELLOW Right Front Gray/Black (-) Gray (+) Right Rear Violet/Black (-) Violet (+) Left Front White/Black (-) White (+) Left Rear Green/Black (-) Green (+) FUSES When replacing fuses, Using an incorrect fuse could damage the radio. The XD5210 uses one .5 amp AGC fuse (Ignition) (Battery) located in-line. Wiring Diagram make sure new fuse is the correct type and amperage. and one 5 amp AGC fuse * CAUTION - Do not attach any speaker leads to ground as severe damage will occur. XD5210 OPERATION Control Locations 89101118 7 1 2 3 4 5 6 17 1213141516 1 2 3 4 5 6 7 8 9 Release Volume Tune/Track Up Band Bass Boost Eject Display Play/Pause Auto Store/Preset Scan 10 11 12 13 14 15 16 17 18 Preset 6 Preset 5 Preset 4/CD Random Preset 3/CD Repeat Preset2/CD Intro Preset 1/CD Top Audio Power Tune/Track Down XD5210 OPERATION General Operation Faceplate Removal Power On/Off CD Mode Tuner Mode Bass Boost Volume Display Set the Clock Press REL and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. *For semi-permanent faceplate installation, remove trim ring and install supplied Phillips head #1 screw through left side of mounting frame into faceplate. Press PWR to turn the unit on. Inserting a CD will turn the unit on automatically. Press PWR to turn the unit off. Insert a CD or press l/ II to begin or resume playback. Press PWR or BAND to begin or resume tuner operation. Press BASS to activate and deactivate bass boost curve. Activating this feature will enhance the bass frequencies when listening to music at low volumes. Adjust volume using VOL ^ or VOL Ў (00-39). Press DISP to display the clock. The radio frequency (tuner mode) or CD track/elapsed time (CD player mode) show by default. Press DISP to display the clock, then release. Press and hold DISP then press TUNE << to adjust the hours and TUNE >> to adjust the minutes. Release DISP to save the selected time. XD5210 OPERATION Reset Audio Bass Treble Balance Fader General Operation Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs. The RESET button is located behind the faceplate. Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. Press AUD until BA appears Press VOLUME Ў or ^ to adjust (6 maximum / -6 minimum) Press AUD until TR appears Press VOLUME Ў or ^ to adjust (6 maximum / -6 minimum) Press AUD until B appears Press VOLUME Ў (LEFT) or ^ (RIGHT) to adjust (BL 16/BR 16) B 00 represents equal balance. Press AUD until F appears Press VOLUME ^ (FRONT) or Ў (REAR) to adjust (FF 16/FR 16) F 00 represents equal balance. XD5210 OPERATION Tuner Operation Seek Tuning Press TUNE << or >> momentarily to seek the next strong station. Manual Tuning Press TUNE << or >> for more than 2 seconds, then press TUNE << or >> momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 2 seconds, the unit will return to seek tuning mode (default). Band Press BAND to select between FM1, FM2, FM3 and AM1, AM2 bands. Storing and Recalling Station Presets Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Automatically Store Stations Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. Preset Scan Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing...