If an extension cord is required, use only a heavy duty cord rated for 15 amps minimum . No other major electrical appliance should be operating on the same circuit. How To Operate Your Heater NOTE: Before operating heater, HEATER INSPECTIONSteps 1 through 3 must be completed: 1) Plug the electrical cord into a 120 volt (AC) outlet. The plug should fit tightly into the receptacle for a proper electrical connection. 2) Rotate the thermostat control knob clockwise until the light illuminates, indi

TOOLS REQUIRED: • Small Flathead Screwdriver • Phillips Screwdriver • Wire Cutter • Cable or Wire Ties • Wire Connectors • Wire Stripper • Crimping Tool • Needle Nose Pliers IMPORTANTINSTRUCTIONS WARNING Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working on the heater. Failure to do so could result in serious electrical shock, burns, or possible death. IF YOU

Failure to do so could result in serious electrical shock, burns, or possible death. IF YOU ARE UNCOMFORTABLE WORKING WITH ELECTRICAL APPLIANCES, UNABLE TO FOLLOW THESE GUIDELINES, OR DO NOT HAVE THE NECESSARY EQUIPMENT, CONSULT A LICENSED ELECTRICIAN. 1. It is important that you verify power has been turned off and no power is going to the heater before proceeding. Circuit breakers are often not marked correctly and turning the wrong breaker off could mean electricity is flowing to the heater,

Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically marked L1). 3. Route remaining thermostat wire (typically marked T1) to the baseboard heater. 4. Route remaining supply and ground wire to the baseboard heater. 5. Follow installation instructions for mounting and wiring baseboard heater. Figure 12To Supply Thermostat wiring box Single Pole Thermostat L1 T1To Heater DOUBLE POLE WALL THERMOSTAT 1. Route supply wir

Failure to do so could result in serious electrical shock, burns, or possible death. CAUTION - High Temperature. Keep electrical cords, drapes, and other furnishings away from heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as

Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein. If you believe your Cadet product is defective, please contact Cadet Manufacturing Co. at 360-693-2505, during the warranty period, for instructions on how to have the repair or replacement processed. Warranty claims made after the warranty period has expired will be denied. Products returned without authorization will be refused. Parts an

Failure to do so could result in serious electrical shock, burns, or possible death. CAUTION - High Temperature. Keep electrical cords, drapes, and other furnishings away from heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as

Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as the heater. 3. All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes. 4. The heater must be grounded to one of the grounding screws provided. 5. If you need to install a new circuit or need additional wiring information, consult a qualified electri

WIRING COMPARTMENT COVER Figure 2 3. Remove the slotted knockout closest to the sup ply wires and install a strain relief connector (See Figure 3). Figure 3 4. Pull supply wires through the connector and secure leaving 6 inch wire leads for later use (See Figure 4). SUPPLY WIRES JUNCTION BOX GROUND SCREW Figure 4 5. Mount the heater securely to the wall with nails or screws going into at least two wall studs (See Figure 5). The back of the heater has “star punch” dimples that allow nails or scre