Light bulbs should be 12V 20W maximum. 5. Using a cloth, hold the new light bulb and push securely into light socket. 6. Return halogen light glass cover to the housing. . 7. Turn range hood ON to test for operation. 20 SPECIFICATIONS MODEL / SIZE CH7930SQB / 30” CH7936SQB / 36" CH7942SQB / 42" CH7948SQB / 48" COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 30” – 232W / 2.21A 36” – 232W / 2.21A 42” – 253W / 2.38A 48” – 258W / 2.41A NUMBER OF MOTORS 2 DESIGN 18-Gauge Seamless / Satin

SUFFICIENT AIR IS NEEDED FOR PROPER COMBUSTION AND EXHAUSTING OF GASES THROUGH THE FLUE (CHIMNEY) OF FUEL BURNING EQUIPMENT TO PREVENT BACK DRAFTING. FOLLOW THE BEATING EQUIPMENT MANUFACTURER’S GUIDELINE AND SAFETY STANDARDS SUCH AS THOSE PUBLISHED BY THE NATIONAL FIRE PROTECTION ASSOCIATION (NFPA), AND THE AMERICAN SOCIETY FOR HEATING, REFRIGERATION AND AIR CONDITIONING ENGINEERS (ASHRAE), AND CODE AUTHORITIES. 2 - IMPORTANT SAFETY INSTRUCTIONS - WARNING – TO REDUCE THE RISK OF PERSONAL INJURY

7. STAND ALONE INSTALLATION ........................................................................................................... 9. 6 UNDER THE CABINET INSTALLATION Preparation before Installation Figure 1 NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. . Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. . A straight, short venting run will allow the hood to perform more efficiently. . Try to avoid as many transitio

What to Do If You Smell Gas • Extinguish any open flame. • Do not try to turn on the lights or any type of appliance. • Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue

Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood, if any. • Use duct tape to seal joints between pipe sections. • For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not pr

Press either Speed Control button once (will start on Low speed) for fan control. See Fig. 4. 3. Press Speed Control button to cycle from QuietMode. through high speed. See Fig. 4. 4. Press Light Control button to turn light on. Turn Off: 1. Press Power Control button once (panel lights will flash for 10 seconds before power will completely shut off). 2. Press Power Control button twice (all power will shut off immediately). 3. If only lights are on, pressing Power Control button once will turn

Access the wire connections underneath the hood by removing the bottom casing from the six screws. Before reattaching the bottom casing, make sure wires do not slip between motors, impellers, or any moving parts to prevent any damage. -Connect three wires (black, white and green) to house wires and cap with wire connectors. -Connect according to color: black to black, white to white, and green to green. -Test the operation of the hood before moving on to the next step. Make sure power is supplie

4) Activating any switch on may cause ignition or an explosion. 5) Due to the size and weight of this hood, installation by 2 persons is recommended. ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes. COMPONENTS OF PACKAGE (Must keep all material for returns or refund

BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green. -If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood. Make sure wires do not

Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. 3. DO NOT allow deposits to accumulate or remain on the hood. 4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. 5. DO NOT a