Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
7. STAND ALONE INSTALLATION ........................................................................................................... 9. 6 UNDER THE CABINET INSTALLATION Preparation before Installation Figure 1 NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. . Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. . A straight, short venting run will allow the hood to perform more efficiently. . Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. . Temporarily wire the hood to test for proper Figure 2 operation before installing. . Important: Peel protective film off the hood (if any). . For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 2. . Measure and create access opening for electrical wires under the cabinet. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. Figure 3 SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes on the hood as shown in Figure 3. 2. Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (included). Shown in Figure 4. 3. Using references on Table 1 and measurements on page 15-16 center the hood in place beneath the cabinet and flush with the front of the cabinet. 4. Draw electrical wires through cabinet access Figure 4 opening. 5. From the bottom of the hood, place screw (not provided) into the exact center of each knockout hole. Make sure all screws are in place before tightening screws. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING. 6. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included). 7 Ductwork Installation Ductwork Installation Figure 5 7. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 8. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green as shown on Figure 6. -If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood. Make sure wires do not slip between motor or any moving parts to prevent any damage. Install Accessories Figure 6 Figure 7 Figure 8 9. Attach Oil Tunnel. Refer to Figure 7. 10. Refer to Figure 8. Slide the baffle filter into the hood. Push the baffle filter upward. . Slide forward. Pull downward. Fit into place. 11. Repeat for all baffle filters and spacers. Refer to page 17. 12. Install heating lamps (not included), 120 Volts 175 Watts max. each. Final Assembly 13. Turn power ON in control panel. Check all lights and fan operation. 14. Make sure to leave this manual for the homeowner. 8 STAND ALONE INSTALLATION ***This installation only applied with the purchase Figure 9 of an optional duct cover: Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. . Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. . A straight, short venting run will allow the hood to perform more efficiently. . Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. . Use duct tape to seal the joints between pipe sections. . If necessary, prepare back wall frame with cross framing lumber for secure installation. . Using references on Table 2 and measurements on page 16-17, decide the level of the lumber. Refer to Figure 10. Hood Preparation before Installation • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood and the duct cover (if any). • Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (included). Refer to Figure 11. • If necessary, attach two rubber stands (included) with adhesive tape (included) to the back corners of the hood. • Use eight (3/16” x 3/8”) screws (included) to attach the two hood-mounting brackets (included) to the back of the hood. Refer to Figure 12. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the pow...
Эта инструкция также подходит к моделям:Вентиляторы - CH-100 CH0030SQB (1.41 mb)
Вентиляторы - CH-100 CH0042SQB (1.41 mb)
Вентиляторы - CH-100 CH0048SQB (1.41 mb)