....................................1 .................JI-X04-B...................Capacitor (motor – not shown).............................300MFD 125VAC........1 .................JI-X04-CA................Capacitor Cover................................................... ....................................1 .................JI-X04-DA................Junction Box (motor – not shown)....................... ....................................1 .................JI-X04-EA.................Junction Bo

8 Installing Pen Mandrel Screw the mandrel (A, Fig. 10) into the threads in the headstock spindle and place the other end on the tip of the live center of the tailstock as shown. The barrel(s) of a pen can be placed between bushings, and held snug on the mandrel by the knurled nut (B, Fig. 10). If you are new to the practice of pen turning, a book entitled “Pens from the Wood Lathe” (stock # 709123) will demonstrate techniques and tips on turning, and is available from WMH Tool Group. Complete s

BD920N-CS09......... .........Rivet............................................... ..................2x5................ ...........2 10 ... 5020......................... .........Graduated Ring.............................. ...........1 11... ... BD920N-CS11......... .........Key................................................. ..................3x13.............. ............1 12... ...5023......................... .........Spring............................................. ............1

M-708376 Ph.: 800-274-6848 Revision A 9/06 Copyright © WMH Tool Group WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. Fo

16). JET offers a wide variety of hoses, adapters and dust collectors. 2. Loosen the wing nut (B, Fig. 16) and pull the gate (C, Fig. 16) open to allow air suction to the sanding belt. Push the gate closed to shut off air suction. Tighten the wing nut. 3. Push the gate (D, Fig. 16) down to shut off air suction to the disc. Lift the gate to open the air suction to the disc. Lubrication All moving parts run on sealed ball bearings and require no lubrication. Optional Accessories Open Stand w/Belt

This warranty gives you specific legal rights, and you have other rights, which vary, from state to state. JET Equipment &Tools. P.O. Box 1349, Auburn, WA 98071-1349 . (253) 351-6000 2 Lt WARNING For your own safety, read the owner's manual before operating the shears. This shear is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a shear, do not use until proper training and knowledge has been obtaine

Now, the new JET JWL-1220VS lathe brings variable speed to this instantly popular machine. Add the JWL1220BE 28” bed extension and the JET JWL-1220VS 50” between centers capacity rivals that of many larger, more expensive lathes. The JET JWL-1220VS lathes are built using our time honored heavy cast iron technology to insure maximum accuracy and the long-term durability that makes the JET JWL-1220VS Wood Lathe an even greater value. Power and Speeds Pulley Position The JET JWL-1220VS lathe featur

With features like a 25/32" spindle bore, a MT#3 tailstock and 6 spindle speeds you'll be able to turn some surprisingly hefty projects! If you're thinking of making parts for models, engines or even for repairs around the home or shop, this is the jettools.com JET 9" x 20" BELT DRivE BENcH LATHE 4 Way ■ Tool y Post j/ Enclosed Quick Change " Gear Box Adustable Tailstock d 4 L ■ ?- Ü.T Hardened and Ground Bedways Optional Stand 9" x 20" BELT DRivE BENcH LATHE • Spindle suppor

.................................................1 9...............6294132...................Shaft..................................................................... .................................................1 .............6294133...................Gear..................................................................... .................................................1 11 .............6294134 ...................C-Clip ...................................................................

A good rule of thumb when sanding with grits finer than 80 is lower the drum so that it contacts with work piece but still can be rotated by hand. When using grits coarser than 80 grit, you can lower the drum slightly more. However, a combination of several variables will determine the proper depth of cut to use, including the following: • Abrasive type and grit size. • Width of the piece being processed. • Hardness of the piece. • Feed rate of stock. Establishing the Proper Drum Height To estab