Оценок - 4, средний балл: 3
(
)
)
|
Фрагмент инструкции
16). JET offers a wide variety of hoses, adapters and dust collectors. 2. Loosen the wing nut (B, Fig. 16) and pull the gate (C, Fig. 16) open to allow air suction to the sanding belt. Push the gate closed to shut off air suction. Tighten the wing nut. 3. Push the gate (D, Fig. 16) down to shut off air suction to the disc. Lift the gate to open the air suction to the disc. Lubrication All moving parts run on sealed ball bearings and require no lubrication. Optional Accessories Open Stand w/Belt Rack 708596 Closed Stand w/Belt Rack708597 JET Stik Abrasive Belt and Disc Cleaner 57620025 Dust Collectors and Accessories see JET Distributor JSG-96 Sanding Belts, Master Carton 10 6”x48” 24 Grit 40 Grit 60 Grit 80 Grit 100 Grit 120 Grit 150 Grit 180 Grit Close d Coat 57617110 57617210 57617410 57617510 57617610 57617710 57512210 57512310 Open Coat 57432910 57422110 57422210 57422310 57422410 57422510 57422610 57422710 JSG-96 Sanding Disc PSA Aluminum Oxide Cloth Back Sanding Disc, Master Carton 25 9” 36 Grit 50 Grit 60 Grit 80 Grit 100 Grit 120 Grit Close d Coat 57697525 57697650 57697750 57697850 57697950 57698050 13 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord Sanding belt does not come up to speed 1. Extension cord too light or too long 2. Low current 1. Replace with adequate size and length cord 2. Contact a qualified electrician Machine vibrates excessively 1. Stand on uneven floor 1. Adjust stand so that it rests evenly on the floor Abrasive belt keeps tearing 1. Belt is running in the wrong direction 1. Arrow on the sanding belt and machine should be pointing in the same direction. Sanded edge not square 1. Table not square to sanding belt 2. Miter slot not parallel to sanding belt 1. Use a square to adjust table to sanding belt 2. Use a square to adjust the table’s miter slot parallel to the sanding belt. Sanding marks on wood 1. Work held still 2. Wrong grit sanding belt 3. Feed pressure too great 4. Sanding against the grain 1. Keep workpiece moving 2. Use coarser grit for stock removal and fine grit for finish sanding. 3. Never force work into sanding platen 4. Sand with the grain 14 Disc Sander Assembly Breakdown 15 Parts List For The JSG-96 Sander Disc Sander Assembly Index Part No. No. Description Size Qty. 1..........JSG96-101....................... Base.............................................................. ...................................1 2..........JSG96-102....................... Motor............................................................. ...................................1 ............JSG96-102A .................... Starting Capacitor (not shown)....................... ...................................1 ............JSG96-102B .................... Running Capacitor (not shown)...................... ...................................1 3..........TS-1550041..................... Flat Washer................................................... M6..............................4 4..........TS-1551041..................... Lock Washer.................................................M6..............................7 5..........TS-1540041..................... Hex Nut......................................................... M6..............................1 6..........JSG96-106....................... Disc Cover .................................................... ...................................1 7..........JSG96-107....................... Screw w/Washer............................................ 1/4x3/8 .......................3 8..........JSG96-108....................... Air Controller................................................. ...................................1 9..........TS-0813032..................... Screw............................................................ 1/4x1/2 .......................2 10........JSG96-110....................... Lock Knob..................................................... ...................................1 11........JSG96-111....................... Tap Screw.....................................................1/4x1..........................1 12........JSG96-112....................... Key................................................................ 5x5x25 .......................1 13........JSG96-113....................... Disc............................................................... ...................................1 14........JSG96-114....................... Set Screw...................................................... #10x3/8 ......................1 15........JSG96-115....................... Sanding Disc................................................. ...................................1 16........JSG96-116....................... End Cover..................................................... ...............................
Эта инструкция также подходит к моделям:Шлифовальные станки - JSG-96 (1.07 mb)