0 Cosmopolitan This recipe makes two martinis. ice cubes to max ice fill line 4 ounces citrus flavored vodka 2 ounces Cointreau® 2 ounces cranberry juice juice of . lime lemon twists Fill your Waring Pro™ Martini Shaker with ice. Add the vodka, Cointreau®, cranberry juice, and lime juice to shaker. Cover shaker with shaker strainer and insert the shaker into the unit. Press shake. Remove shaker from unit and remove shaker cap, then strain into 2 chilled martini glasses. Garnish each glass with a

Unsweat all tubes from the old compressor. Do not cut them off. 2. Place the new compressor into the ice machine, as shown. 3. This replacement compressor may be different than the original compressor and/or have slightly different tubing configurations. The suction line, discharge line, and/or suction service line at the compressor may need to be rerouted, when making this change-out. 4. Replace the compressor components (start relay, start capacitor, and run capacitor) with the new ones pro

Refrigerant oil must be used to lubricate the fittings. 4. Leak check all joints. 5. Place the four labels, 8136193, included, as follows: two on the ice machine (one by each serial plate), one, as shown below, and one at the discretion of the installer. 6. ATTENTION INSTALLER: Add the following refrigerant at the time of installation: Q-0600 Series - add four (4) pounds Q-0800 Series - add four (4) pounds Q-1000 Series - add two (2) pounds Q-1300 Series - Add nothing Manitowoc Ice, Inc. 2

Alarm sound is only muted, not disabled. If the condition(s) that caused the alarm(s) continue, visual indication will continue and alarm sound will periodically continue for 20 seconds every 60 minutes. 4 APPLIANCE FEATURES Insert Wine Bottles The four pull-out shelves each hold eight bottles. See Figure 4 for typical wine bottle spacing. Tall bottles should not be loaded on the bottom rack because they may prevent the door from closing. The display shelf at the top of the cabinet holds seven b

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the unit’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. 3 LOCATION OF CONTROLS AND INDICATORS 3

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8010113 Web Site - Rev. 06/28/01

Install, as shown. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8009063 Rev. 12/09/97

The K00143 is used for stacking a J/Q-1300 or J/Q-1800 on a Q-1300 or Q-1800 ice machine. (The Q-series ice machine must be on the bottom.) Note: The bin must be level before proceeding to step 2. When this kit is used with K00139 or K00170, the water curtain stop bracket must be cut off from the K00139 or K00170 ice chute. 2. Installation of ice machines: A. See installation manual for uncrating and inspection of both ice machines. B. Remove the top cover from the lower ice machine. C. S

(Note: Do not install transformer to outlet box at this time.) B. Relay Installation (Figure 1) 1. Remove remote condenser fan cover. 2. Remove electrical enclosure box between two fan support brackets. 3. Mount relay(s) to relay bracket with #6-32 screws and nuts. 4. Loosen fan support brackets enough to slide relay bracket between condenser housing and fan support bracket (Figure 1). 5. With relay bracket in place, tighten fan support brackets. C. Wiring Connections (Figure 2, "G" Serie

As you are viewing the ice machine from the front, the replacement compressor is mounted with the suction, discharge, and process ports facing the right side. With the existing tubing, reposition the discharge and process tube to the ports provided on the new compressor. With the suction tube provided with the compressor, insert unswedged end into the suction port, line up to the existing suction line, mark the line, and cut to fit. Note: reducer bushings are provided for suction and process por