Improper adjustment can result in tool failure or other serious hazards. For added stability, attach Side Han1. dle (5) to side of Hammer Case (4) using Bolts (6) and Washers (7). . Work Piece and Work Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. Route air hose along a safe route 2. to reach work area without creating a tripping hazard or exposing air hose to possible damage. Also avoid

Clean with a dry brush. Be careful not to damage the electric grid. Keep the Solar Panel clear of dirt and dust with a damp cloth. Inspect periodically. People with pacemakers should consult their physician (s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Fre

Plug the adapter’s two prongs into the outlet, and replace the center screw. Now plug the tool or machine into the adapter. DO NOT MODIFY THE PLUG IN ANY WAY. IFYOU HAVE ANY DOUBT, CALL A QUALIFIED ELECTRICIAN. Extension Cords If your tool is double insulated and has a two-prong plug, you may use either a two or three-prong extension cord. If your tool has a grounded, three-prong plug, you must use a three-prong extension cord with three-prong receptacles. Only use rounded jacket extension cords

fastening torque 125 N.m (1,110 in.lbs) 140 N.m (1,240 in.lbs) Overall length 163 mm (6-3/8") Net weight 1.5 kg (3.3 lbs) 1.7 kg (3.7 lbs) Voltage 12 V 14.4 V Dimension Model 6980FD 163 mm (6-3/8") Model 6935FD 163 mm (6-3/8") Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan PRINTED IN JAPAN Z23112-2 2003-12 A world's leading manufacturer of power tools & Variable Speed Built-in Job Light V Reversing Carrying Case (4) Electric Brake Cordless Impa

1. Turn on the unit with the Switch on the control panel. See FIGURE 4 on page 6. 2. If, after the unit has warmed up, you don’t hear the fan running, there is likely not enough pressure to turn on the pressure switch. Turn off the unit and the compressor. Close the Air Inlet (#6). Then, turn the Air Dryer back on and it will build up pressure in a few minutes. Open the Air Inlet (#6). Turn on your compressor and let air in slowly at first. During operation, dry air will pass through the unit to

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353. SAVE THIS MANUAL You will need this manual for the safety instruc- READ ALL INSTRUCTIONS BEFORE tions, assembly and operating instructions and ASSEMBLING OR OPERATING THE parts list. Put it in a safe, dry place for future _BEAD ROLLER._ ref

For Household Use Only. 9. Do not let cord hang over edge of table or counter. 10. Do not let cord contact hot surface, including stove. 11. Do not use fingers to scrape food away from discharge disc while appliance is operating. Cut type injury may result. SAVE THESE INSTRUCTIONS. SAFETY SETUP OPERATION MAINTENANCE Work Area Safety 1. Do not use outdoors. 2. Do not place on or near a hot gas or electric burner, or in a heated oven. 3. Extreme caution must be used when moving appliance. 4. Keep

7. Do not abuse the Power Cord. Never use the Power Cord to carry the tool or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. PERSONAL SAFETY 8. Stay alert. Watch what you are doing, and use common sense when operating this product. Do not use the Fountain while tired or under the influence of drugs, alcohol, or medication. A moment of inattention

6. WARNING! The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code 25249.5, et seq.) 7. WARNING! The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and 35558 35559 SKU For technical questions, please call 1-800-444-3353

Release pressure. The Fuse Holder will be flush with the rim of the Fuse Holder Socket. REV 10b Troubleshooting Problem Possible Causes Likely Solutions Motor and Electrical Lathe will not start or a breaker trips on startup. Cord not connected.1. No power at outlet. 2. Fuse has blown. 3. Chuck Guard safety interlock not 4. in place. PC Board (182) faulty.5. Power Switch (178), Forward/6. OFF/Reverse Switch (181) and/ or Speed Control Knob (180) not working. Internal damage or wear. (such 7. as