Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
white paper
HP
NetServer
Netserver
Documentation
Installation and Configuration
Functional Diagram of the Direct Connect Cluster
(SPOFless)
Most of the procedure for installing a SPOFless cluster is
Public Network
identical to the installation of a SPOF cluster solution.
Subsections below only document the differences between
a standard cluster installation and a SPOFless cluster
installation. For more details on how to install and configure
Cluster
Cluster
Private
MSCS, take a look at the References section at the end of
Server
Network
Server
this document.
#1
#2
FC HBA
FC HBA
FC Array Assistant Installation
The most important thing to know when installing FC Array
Failure
Assistant is to install the SPOFless version, A.00.02-5. The
Causes
Port 1
Port 0
Port 1
Port 0
Application
SPOFless version of FC Array Assistant allows mirroring of
Failover
the LUNs, a feature not found in the standard version, but
which is necessary for SPOFless clusters. Additionally it is
External
important to remember that the server portion and the client
SCSI #2
SCSI #1
Shared
Storage
portion of FC Array Assistant must come from the same
installation disk.
SCSI #2
SCSI #1
Another factor concerning the installation of FC Array
Assistant is the location of the FC array client. In practice, it
is advisable to install a copy of the client on each cluster
Copper Fibre Active
SCSI Cable
node and on the client monitor to ensure it is available
during periods of network instability.
RS/12FC External Shared Storage Configuration
The FC Array Assistant utility is used to configure, manage
Functional Diagram of the Cluster Using Hubs
(SPOFless)
and monitor RS/12FC storage. The Manual Configuration
Public Network
mode is recommended because it provides more control
over the setup of different parameters compared to the
Automatic or Assisted Configuration modes. Manual mode
allows the addition of new RAID sets, addition of logical
Cluster
Cluster
Private
drives or editing of the existing configuration.
Server
Network
Server
#1
#2
Failure
Causes
Application
After FC controllers have been configured they can be
FC HBA
FC HBA
Failover
monitored, as can physical devices and logical drives in the
RS/12. Performance monitoring is also implemented in FC
FC Hub
FC Hub
Array Assistant. To learn how to use the FC Array Assistant
tool, refer to the References section at the end of this
Port 1
Port 0
Port 1
Port 0
document. An example of the Controller Information screen
is shown on page 6.
Failure
External
Causes
SCSI #2
SCSI #1
There are two main issues concerned with the configuration
Shared
Decreased
Storage
Performance
of the RS/12FC storage subsystem. The first issue has to
do with the consistency of the firmware installation on the
SCSI #2
SCSI #1
two FC Array controller cards. Before attempting to use
both controllers in the same RS/12FC cabinet it is important
to download the firmware individually to each controller.
Copper Fibre Active
Optical or Copper Fibre
This means that the firmware of each controller must be
Copper Fibre Passive
SCSI Cable
checked individually in an RS/12 FC cabinet before it can
be used in tandem with another controller.
Also, when flashing the firmware on the controller, the
various configuration parameters on the controller are not
reset. This means that before two controllers are bound
5
...Эта инструкция также подходит к моделям:
Компьютеры - HP NetServer LC 2000 (67.85 kb)
Компьютеры - HP NetServer LC 2000r (67.85 kb)
Компьютеры - HP NetServer LC II (67.85 kb)
Компьютеры - HP NetServer LC Plus (67.85 kb)