Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Replace Covers and Connect Cables
9 1.Replaceallcovers:
Seat Top
A. If a side cover was removed, insert its lower channel onto the lip
B Rear Tabs
at the bottom of the chassis. Press the top of the side cover
First
against the chassis, so that it snaps into place.
Ensure
A
Tabs
Seat
B. To replace the top cover, align both corners of its rear edge
Seat
against the metal tabs on the rear of the HP NetServer. Lower
Side
the front of the top cover and pull it forward slightly to catch on
Cover
the rear of the chassis and to clear the front edge of the chassis.
Tighten both thumbscrews.
Then Swing
C. Align the front bezel against the front of the HP NetServer, and
C Front
Top Cover
press it firmly into place. Lock the front bezel with the key
Bezel
into Place
provided.
2. Connect the power cord and all other cables.
CAUTION
Replace ALL covers before operating the
HP NetServer, even for a short time.
Otherwise, overheating can damage
processors, boards, and mass storage
devices.
Verify Installed Accessories
NOTE
SCSI devices connected to a disk array controller board
(Optional)
10
(DAC) cannot be displayed at boot time. An ISA non-
Plug-and-Play board cannot be displayed at boot time.
The boot screen lists the hardware that the system detected, such as
If you wish, you may now verify accessories you have installed. Turn on
CPU, DIMMs, and PCI and ISA boards. If the system fails to restart, follow
the HP NetServer and monitor, and view the the boot screen.
the instructions on the screen.
Configure the HP NetServer
11
3. Select the NOS: Select the NOS you will install, including version if
necessary. Installation of the optional IntranetWare NOS, which is in the
HP NetServer Software Option Package, requires the key obtained in
Step 4 of this Road Map: "Prepare for Hardware Installation."
4. Select the NOS installation mode: If you select certain versions of
1. Turn on the HP NetServer and monitor, and insert the HP Navigator
Novell NetWare / IntranetWare or Microsoft Windows NT Server, you
CD-ROM into the drive. Turn the power off, wait 10 seconds, and turn
will be asked, "Would you like to use HP's automated mode of NOS
the power on again. If the system fails to boot, follow the instructions on
installation?"
the screen.
If you want to use automated NOS installation, select "Yes." Choose
automated NOS installation mode for first-time installation of Novell
NOTE
If you have installed an ISA non-Plug-and-Play
NetWare / IntranetWare or Microsoft Windows NT Server on a factory-
accessory board, you must reserve system
configured HP NetServer LC 3.
resources for it by using the Setup utility. Start the
Setup utility by pressing the F2 function key when
Perform a manual NOS installation if you are installing a NOS other
"Press
than Novell NetWare / IntranetWare or Microsoft Windows NT Server,
screen.
or if you replaced HP components. (For example, if you replaced an HP
network interface controller board with a third-party board, install the
When the Setup utility starts, select "Configuration,"
NOS manually.)
and then select "ISA non-Plug-and-Play Devices."
5. Configure Remote Management: If you plan to manage the HP
Use the arrow keys to highlight a selection, press
NetServer LC 3 remotely, refer to the HP NetServer LC 3 Remote
ENTER to display its options, and use the +/- keys to
Administrator Guide. Select "Configure Remote Management" on the
change values. When done, save changes and exit.
Configure Remote Management screen to start the utility that
For more about reserving system resources, refer to
configures Integrated Remote Assistant.
Information Assistant and to "Configuring ISA Non-
Plug-and-Play Board" in the HP NetServer LC 3
6. Configure Disk Array: If you have a disk array, refer to the HP
User Guide.
NetRAID Series Installation and Configuration Guide. Select "Execute"
on the Configure Disk Array screen to start the utility that configures the
(If the system hangs before the Setup utility starts,
disk array.
remove the ISA non-Plug-and Play board, run the
7. Install the NOS: If you selected the HP automated NOS installation
Setup utility to reserve system resources for it, and
process, you will be guided through the process by a series of HP
reinstall the board.)
display screens.
2. Run Configuration Assistant and Installation Assistant: Go to the
To install the NOS manually:
HP Navigator Main Menu. If you want to change the language, select
"Set Preferences" and the language. Select "Configuration and
On the Create Driver Diskette(s) screen, select "Create Drivers
Installation Assistant." Select "Express" from the next screen to begin
Diskette(s)."
the "Express" mode of configuration.
On the Show NOS Installation Instructions screen, select "Save to
"Custom" configuration mode and "Replication" configuration mode are
Disk." Then print out the Network Operating System Installation
also available. Refer to the HP NetServer LC 3 User Guide for details.
Instructions from the disk. Read these instructions before starting to
install the NOS.
NOTE
To use the Console Redirection feature of Integrated Remote
Follow the instructions on the screen and the Network Operating
Assistant to run server management utilities remotely, you
System Installation Instructions to perform the manual NOS installation.
must create the utility partition. "Express" configuration mode
creates it automatically. If you use "Custom" configuration
8. HP NetServer management: Refer to the HP NetServer Management
mode, create the partition by selecting "Install/Update Utility
Reference Guide, and install HP TopTools.
Partition" from the Custom Configuration menu within
Configuration Assistant.
Install the NetServer in the
To install the HP NetServer in a rack assembly, refer to the following:
Rack (Optional)
12
! Rack installation kit instructions
! HP NetServer LC 3 User Guide
!` The HP Web site: http://www.hp.com