Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации HP, модель HP NetServer LC 3

Производитель: HP
Размер: 105.9 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


HP NetServer LH 6000 / LH 6000r Technical Reference Card
Placeholder for Bar code
HP Product No. D9103-80201, Feb. 2000
A
Caution: Do not operate server
Cabinet
Front
Rack Version
for more than 30 minutes with
Panel Display
Pedestal Version
any cover (including Power
I/O Fan Assembly
Door reveals this panel
Supply Bays and Disk Drives)
removed. Processor will shut
System Board
Power-on
Reset
I/O Board
LED
Switch
down if overheated.
Assembly
Power
Secure
Processor
Mode
Power Mgmnt/
Fans
Lock
LED
Interconnect
Reset
Shelf 1: Flexible
Disk Drive
Status
Server
Optional
Screen
Status
Power
Exhaust
Shelf 2:IDE
LEDs
Supply (4)
Fans
CD-ROM Drive
Power
Supplies
Default Boot Order
Escape
Unused
Scroll
Shelf 3 & 4: Optional
Up
1. IDE CD-ROM
Mass Storage
Enter
Scroll
Down
2. Flexible Disk Drive
A
Front Panel Console
B
System Board
3. Embedded SCSI
Power Supply Fans
Assembly
(Pairs A & B)
PCI Slots
4. Other SCSI B Device
* Note that a simplex cable is used at
(Settable)
Primary Hot-Swap
Secondary Hot-Swap
HDD Slots 1 – 6 *
the back of the primary and secondary
I/O Connectors
Cage (optional) *
hot-swap HDD cages.
(Rear View)
(Front View)
B System Board Assembly
Fan Mounting
C General Information
Blind Mate
Processor Slots (1-3)
For more information, visit the Web site at www.hp.com/go/netserver.
Connectors
HP has offices in over 100 countries. Check your local telephone directory.
1
Audience Assumptions
2
This Technical Reference Card is for trained service personnel. Hewlett-Packard Company assumes
3
you are qualified in the servicing of computer equipment and trained in recognizing hazards in
1A (1)
DIMM
2A (2)
products with hazardous energy levels.
Slots
3A (3)
Electrostatic Discharge
4A (4)
To avoid catastrophic or hidden damage to components, wear a wrist strap and use a static
Voltage
Serial
1
4
dissipative work surface connected to the chassis when handling components.
Regulator
5
2
This information is subject to change without notice and is provided without warranty.
Module
Slots (1-6)
6
3
© Copyright 2000, Hewlett-Packard
Parallel
1B (5)
DIMM
2B (6)
Slots
Mouse
3B (7)
4B (8)
Keyboard
D Quick Reference
LAN
DIMM Installation
NOTE: Slot numbers
6
Video
• Use up to 8 HP SDRAM DIMMs in sizes of
• Maximum system size is 8GB.
as used in event logs
128MB, 256MB, 512MB, and 1GB.
• Different sizes of approved memory may be
are in parentheses.
• DIMMS are supplied in Slots 1A and 1B.
used in different slots.
5
Fan Mounting
• Memory must be added in pairs, one in slot A
• Add paired memory DIMMs in any order to any
Configuration
CMOS
and one in slot B.
open slots (2A/B, 3A/B, or 4A/B).
Switches
Battery
Processor Slots (4-6),
• When a pair of DIMMS are added, both must
Terminators shown
4
be of the same size.
For additional information, see other side.

...

Эта инструкция также подходит к моделям:
Компьютеры - HP NetServer LC 2000 (105.9 kb)
Компьютеры - HP NetServer LC 2000r (105.9 kb)
Компьютеры - HP NetServer LC II (105.9 kb)
Компьютеры - HP NetServer LC Plus (105.9 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории