Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Mouse
Keyboard
10MakeExternalConnections
AC Power
Connector
Make external connections, such as the monitor, keyboard, and mouse cables, UPS,
and the AC power cord to the appropriate connectors on the rear of the chassis as
instructed in the Rack Cabling Guide Reference for the HP NetServer LH 4r. Note that
Monitor
four power supplies are shown here.
AC Power
Connector
Rear View
Configure the HP NetServer
9. View Configuration Advisories: Read the Configuration
11 1. BoottheHPNavigatorCD-ROM:Turnonthe
Advisories and print them if necessary. Make any changes suggested
monitor. Press the power-on button on the HP NetServer,
in the advisories.
and press the eject button on the CD-ROM drive. Place the
10. Configure Remote Management: If you plan to manage the
HP NetServer Navigator CD-ROM in the drive and close the
HP NetServer LH 4 remotely, refer to the HP NetServer Server
drive. Press the Reset button. If the system fails to restart,
Management Reference Guide for instructions. Select "Configure
follow the instructions on the screen.
Remote Management" on the Navigator screen to configure
Integrated Remote Assistant.
NOTE
If you have installed an ISA non-Plug-and-Play
11. Show System Information: Select "View System Information"
accessory board, you must reserve system
to get information about accessory boards and devices. Select "View
resources for it by using the Setup Utility. Start
Resources" to view used and available system resources.
the Setup Utility by pressing function key [F2]
when prompted during the boot process.
12. Configure Mass Storage. This NetServer is shipped with the
hot-swap mass storage device(s) unconfigured. To configure the
For more information about reserving system
drive(s), do one of the following:
resources for ISA non-Plug-and-Play, and other
!
,
devices refer to Information Assistant and to
Run HP NetRAID Assistant to configure one or more RAID logical
"Configuring ISA Non-Plug-and-Play Board" in
drives. To run HP NetRAID Assistant, select "Execute" from the
Chapter 4, "Accessories," in the HP NetServer
Configure Disk Array screen.
LH 4/LH 4r User Guide.
! Exclude SCSI A Channel from the integrated HP NetRAID
controller, as follows:
!a. Restart the HP NetServer.
When HP Navigator starts, you can set the time and date,
!b. Press function key [F2] when prompted on the boot screen.
and change the display language.
!c. When the SETUP utility menu is displayed, use the up and down
arrow keys to highlight the "Include SCSI A Channel [Yes]"
2. Read the Readme File: Select "Readme File" from the
selection.
HP Navigator Main Menu. The Readme file contains the
!
latest information to help you install your HP NetServer.
d. Use the + and - keys to change it to "Include SCSI A Channel
[No]."
3. Run DiagTools (Optional): To verify the HP
!e. Press function key [F10] to save the configuration and exit the
NetServer hardware as shipped, run DiagTools by first
utility program.
creating a DiagTools flexible diskette from the HP NetServer
!
Navigator CD-ROM. For more information on how to use
f. Answer "Yes" to the question "Save Configuration and Exit
DiagTools to detect all processors and memory on the
Now?" The HP NetServer will reboot, and HP Navigator will
system board, refer to HP NetServer DiagTools Error
restart.
Reference and User Guide.
13. Install the NOS: If you selected the HP automated NOS
installation process, you will be guided through the process by a
4. Install Information Assistant: Information Assistant
series of HP display screens:
will help you install your HP NetServer. It is easier to use
from a stand-alone system, rather than from the HP
! Install Utility Partition: This step creates a disk utility partition on the
NetServer you are installing. Install Information Assistant
server boot hard disk drive where HP Navigator will copy
from the HP NetServer Online Documentation CD-ROM
troubleshooting and other utilities. The utility partition is not
onto the client system that you will be using to manage your
available under SCO® UNIX. Select "Execute" on the Install Utility
HP NetServer.
Partition screen to install the partition.
! Execute Card Utilities: Select "Execute" on the Execute Card
5. Visit Order Assistant (optional) on the Internet at
Utilities screen to run the accessory board configuration utilities.
http://www.hp.com/go/netserver
! Follow the instructions on the screen and in the network operating
Order Assistant lists HP accessories, cables, and
system's installation instructions to perform the manual NOS
connectors for your HP NetServer.
installation.
!
6. Run Configuration Assistant and Installation
For Manual NOS Installation Only: Before you perform a manual
Assistant:
NOS installation, print out instructions and create NOS-specific
If you want to change the language, select
drivers diskette(s), as follows:
"Set Preferences" from the HP Navigator main menu and
!
choose a language. Select "Configuration and Installation
A. Create Drivers Diskette(s): On the Create Drivers Diskette(s)
Assistant." Select "Express" from the next screen to begin
screen, select Create Drivers Diskette(s) to create one or more
the "Express" mode of configuration.
customized diskettes containing HP drivers and configuration
files to use when you install the NOS.
"Custom" configuration mode and "Replication"
!
configuration mode are also available. Refer to the HP
B. Print and Read Instructions: On the Show NOS Installation
NetServer LH 4/ LH 4r User Guide for details.
Instructions screen, select "Save to Disk" to copy the NOS
installation instructions to disk. Then print them from disk. Read
7. Choose a NOS: Select the NOS you will install, and the
the instructions first, and then follow them to manually install the
version, if necessary.
NOS.
! Install NOS:
8. Select the NOS installation mode: If you select
®
®
®
!
certain versions of Novell NetWare / IntranetWare or
A. Automated NOS Installation: For certain versions of Novell
Microsoft® Windows™ NT Server, you will be asked, "Would
NetWare / IntranetWare or Microsoft Windows NT Server,
you like to use HP's automated mode of NOS installation?"
Configuration Assistant formats and partitions the hard disk
drive. Installation Assistant then guides you through the NOS
! Select "Yes" to choose automated NOS installation for
installation and configures the NOS with the appropriate drivers
first-time installation of Novell NetWare / IntranetWare or
for the HP-bundled configuration or for network interface cards
Microsoft Windows NT Server on a factory-configured HP
onHp's Tested Products List.
NetServer.
! B. Manual NOS Installation: Follow the instructions on the screen
! Use the manual NOS installation if you are installing a
and the network operating system installation instructions that
NOS other than Novell NetWare / IntranetWare or
you printed.
Microsoft Windows NT Server, or if you have replaced
14. Install HP TopTools:
accessory components (for example, if you replaced an
Refer to the HP NetServer Server
HP network interface controller board with a third-party
Management Reference
,
Guide and install HP TopTools.
board that is not on HP's Test Products List, use the
15. Refer to Information Assistant on the HP NetServer Online
manual NOS installation).
Documentation CD-ROM, for further information about your HP
NetServer.