Оценок - 2, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
This message is transmitted twenty-four times per quarter note. Echoing of this message depends on the OTHER item in the ECHO settings. STATUS 11111000 F8 Timing clock 2.2 ACTIVE SENSING (FE) Reception Once this message has been received, MIDI communication will be initialized (e.g., Running Status will be cleared) if no message is received for an interval of 400 ms. This message is not subject to echoing. STATUS 11111110 FE Active sensing 2.3 SYSTEM RESET (FF) Reception When this message is received, MIDI communication will be initialized (e.g., Running Status will be cleared). This message is not subject to echoing. STATUS 11111111 FF System reset 3 System Exclusive Message 3.1 Bulk Dump Command rx/tx function F0 43 0n 3E BB BB 11 D0 D1 D2 … rx/tx BULK DUMP EE F7 BULK DUMP DATA DATA F0 43 2n 3E 11 D0 D1 D2 F7 rx BULK DUMP BULK DUMP REQUEST REQUEST The M7CL uses the following data types for a bulk dump. Data name (D0) Data Number (D1,2) tx/rx function ,M‘ 0–300, 512, 768 tx/rx Szenenspeicher & Anforderung (Request) ,S‘ 512–517 tx/rx Szenenspeicher & Anforderung (Request) (aktuelles Setup) ,s‘ 512–528 tx/rx User-Setup-Speicher & Anforderung (Request) ,Y‘ 1–199, 512– tx/rx Dynamik-Library & Anforderung (Request) ,H‘ 0–199, 512–559, tx/rx Eingangskanalbibliothek & 560-567 Anforderung (Request) ,h‘ 0–199, 768–783, tx/rx Ausgangskanalbibliothek & 1024–1031, Anforderung (Request) 1280–1282 ,Q‘ 1–199, 512– tx/rx Eingangs-EQ-Bibliothek & Anforderung (Request) ,q‘ 1–199, 768– tx/rx AusgangsEQ-Bibliothek & Anforderung (Request) ,F‘ 1–199, 512– 527 tx/rx GEQ-Bibliothek & Anforderung (Request) ,E‘ 1–199, 512– 515 tx/rx Effekt-Library & Anforderung (Request) ,P‘ 512 tx/rx Programmwechseltabelle & Anforderung (Request) ,C‘ 512 tx/rx Controller-Tabelle & Anforderung (Request) ,M‘ 0–300 Szenennummer 512 Aktuelle Daten (ohne Recall Safe) 768 Aktuelle Daten (mit Recall Safe) ,S‘ 512 Setup Memory 513 Mischpulteinstellung 514 Ausgangs-Port 515 Monitor 516 MIDI-Einstellung 517 Library-Nummer ,s‘ 512–515 Anwenderdefinierte Tasten 1–4 516–519 Anwenderdefinierte Tasten (Gast) 1–4 520-523 Anwenderdefinierte Tasten (Admin) 1–4 524 Preference 525 Anwenderdefinierte Taste 526 Anwenderdefinierte Taste Gast 527 Preference Gast 528 Preference Admin ,Y‘ 1–199 Library-Nummer 512–559 Dynamik 1 Eingange 1–48 560–567 STIN 1L–4R 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) 1536-1583 Dynamik 2 Eingange 1–48 1584–1591 STIN 1L–4R ,H‘ 0–199 Library-Nummer 512–559 Eingange 1–48, 560–567 STIN 1L–4R ,h‘ 0–199 Library-Nummer 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) ,Q‘, ,q‘ 1–199 Library-Nummer 512–559 Eingange 1–48, 560–567 STIN 1L–4R 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) ,F‘ 1–199 Library-Nummer 512–527 RACK 1A–8B ,E‘ 1–199 Library-Nummer 512–515 RACK 5–8 ,P‘, ,C‘ 512 Aktuelle Daten Data is lost when you write to the preset library. The unique header (Model ID) identifies whether the device is a M7CL. To calculate the check sum, add the bytes starting with the byte after BYTE COUNT (LOW) and ending with the byte before CHECK SUM, take the binary complement, and set bit 7 to 0. CHECK SUM = (-sum)&0x7F Bulk Dumps can be received at any time, and can be transmitted at any time when a Bulk Dump Request is received. A Bulk Dump is transmitted on the [Rx CH] channel in response to a Bulk Dump Request. In the data portion, seven words of 8-bit data are converted into eight words of 7-bit data. Anhange 283 M7CL – Bedienungsanleitung MIDI-Datenformat MIDI-Datenformat d[0. 6]: actual data b[0. 7]: bulk data b[0] = 0; for( I=0; I<7; I++){ if( d[I]&0x80){ b[0] |= 1<<(6-I); } b[I+1] = d[I]&0x7F; } [Recovery from bulk data to actual data] d[0. 6]: actual data b[0. 7]: bulk data for( I=0; I<7; I++){ b[0] <<= 1; d[I] = b[I+1]+(0x80&b[0]); } 3.2 PARAMETER CHANGE Reception This message is echoed if [Parameter change ECHO] is ON. This message is received if [Parameter change RX] is ON and [Rx CH] matches the Device number included in the SUB STATUS. When a parameter change is received, the specified parameter will be controlled. When a parameter request is received, the current value of the specified parameter will be transmitted as a parameter change with its Device Number as the [Rx CH]. Transmission If [Parameter change TX] is ON, and you edit a parameter for which control change transmission has not been enabled, a parameter change will be transmitted with the [Tx CH] as its device number. In response to a parameter request, a parameter change will be transmitted with [Rx CH] as its device number. Command rx/tx function F0 43 1n 3E 11 … F7 rx/tx M7CL native parameter change RARAMETER CHANGE F0 43 3n 3E 11 … F7 rx/tx M7CL native parameter request PARAMETER REQUEST 4PARAMETER CHANGE details 4.1 Current Scene, Setup, Backup, User Setup 4.1.1 Format (Parameter change) Receive Data will be received when [Parameter change Rx] is on and the Device number of both [Rx CH] and SUB STATUS are match...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M7CL-32 (16.68 mb)
Музыкальные инструменты - M7CL-48ES (16.68 mb)