Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
5 When you have finished making settings, press the “.” symbol located in the upper right to close the window. You will return to the OVERVIEW screen. . Selecting the output channel for each output port Here’s how you can select the output channel that will be the output source for each output port. 1 In the function access area, press the SETUP button to access the SETUP screen. OUTPORT SETUP button 2 In the SYSTEM SETUP field located in the center of the screen, press the OUTPORT SETUP button to open the OUTPUT PORT popup window. In the OUTPUT PORT popup window you can assign the source channel for each output port. The popup window includes the following items. 2 1 3 5 6 8 J 7 9 4 1 Slot number / Card type If an output channel of slot 1–3 is selected for operations, this shows the slot number and the type of I/O card installed in that slot. B DELAY SCALE field Here you can select the units for the delay time shown below the delay time knob (5). • METER (343.59m/s) ........... The delay time is shown as a distance in meters, calculated as the speed of sound (343.59 m/s) at an air temperature of 20 °C (68 °F) multiplied by the delay time (seconds). M7CL Owner’s Manual Changing the output patch settings Changing the output patch settings FEET (1127.26ft/s) ...........The delay time is shown as a distance in feet, calculated as the speed of sound (1127.26 feet/s) at an air temperature of 20 °C (68 °F) multiplied by the delay time (seconds). • SAMPLE .........The delay time is shown as a number of samples. If you change the sampling frequency at which the M7CL operates, the number of samples will change accordingly. • msec ...........The delay time is shown in units of milliseconds. If this button is on, the same value is displayed above and below the delay time knob (5). C Output port This indicates the type and number of the output port to which the channel is assigned. D Channel select popup button This button lets you select the channel that is assigned to the output port. The name of the currently selected channel is displayed. E Delay time knob This knob sets the delay time of the output port. Press this knob to select it, and use multifunction encoders 1–8 to adjust the settings. The millisecond value is shown above the knob, and the delay time value in the units selected in the DELAY SCALE field (2) is shown below the knob. F DELAY button Switches the output port delay on/off. G o (Phase) button Switches the phase of the signal assigned to the output port between normal phase (black) and reverse phase (orange). H ATT knob Adjusts the amount of attenuation for the signal assigned to the output port. To adjust this value, press the knob in the screen to select it, and operate multifunction encoders 1–8. You can adjust the setting in 0.1 dB steps over a range of -96 to +24 dB. The current value is shown immediately below the knob. I Level meter This meter indicates the level of the signal assigned to the output port. J Output port select tabs These tabs switch the output ports controlled in the popup window in groups of up to eight ports. 3 Use the output port select tabs at the bottom of the popup window to select the output port you want to control. Each tab corresponds to the following output ports. . ES 1–8, 9–16, 17–24 (M7CL-48ES) These tabs enable you to control EtherSound output channels 1–8, 9–16 and 17–24 respectively. . OMNI 1–8 This tab enables you to control OMNI OUT jacks 1–8. . OMNI 9–16 (M7CL-32/48) This tab enables you to control OMNI OUT jacks 9–16. . SLOT1 1–8, 9–16 . SLOT2 1–8, 9–16 . SLOT3 1–8, 9–16 These control output channels 1–8 and 9–16 of slots 1–3 respectively. . 2TR OUT Control the L/R channels of the 2TR OUT DIGI TAL jack. 4 To assign a channel to an output port, press the channel select popup window for that port. The OUTPUT CH SELECT popup window will appear. The popup window includes the following items. 1 2 1 Channel select tabs These select the type of channel shown in the popup window. Each tab corresponds to the following channels. • OUT CH.......... Shows the output channels (MIX channels 1–16, MATRIX channels 1–8, STEREO L/R channels, and MONO (C) channel). • MONITOR OUT ........... Shows the MONITOR OUT L/R/C channels. • CH 1–32 • CH 33–48 (M7CL–48/48ES only) ........... Shows INPUT channels 1–32 (1– 48) B Channel select button Selects the channel to be assigned to the output port you selected in step 3. HINT • If you selected CH 1–32 or CH 33–48 {M7CL–48 only}, the input channel you selected will be output directly from the corresponding output port. At this time, the channel select button in the OUTPUT PORT popup window is shown as “DIR CH xx” (xx= channel number). (For details on direct output > p. 112). 9 Input/output 107 M7CL Owner’s Manual Changing the output patch settings Changing the output patch settings Changing the input patch settings 5 Use the channel select tabs and the channel select buttons to select the source channel, and press the CLOSE button. Y...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M7CL-32 (11.76 mb)
Музыкальные инструменты - M7CL-48ES (11.76 mb)