Оценок - 2, средний балл: 3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Updating the firmware V1 or V2 to V3, or V3.0x to V3.5x 1. Turn off the power to the M7CL. 2. Connect the USB storage device to the M7CL USB connector, then turn on the power to the M7CL. A .Start Loading ?. message will be displayed. 3. Click the OK button to start loading the firmware. CAUTION: A .Loading.... message will appear during loading the firmware. The indication ........ will be displayed during the loading progress. Do not disconnect the USB storage device or power-off the M7CL while accessing the USB storage device. 4. When the firmware has been loaded, the M7CL automatically restarts and a "Starting System..." message flashes for approximately one minute. While this message is flashing, do not turn off the power. If you have accidentally turned off the power, turn on the power again to resume the initialization. 5. When a "Since M7CL was upgraded, Initialize all memories" popup window (or similar message) appears, press the CLOSE button to close it. 6. When an .Initialize All Memories ?. message appears, press the INITIALIZE button. 7. When an .Are you sure ?. message appears, press the OK button. Initializing the internal memory will be started. 8. When the initialization is complete, press the EXIT button. 9. Remove the USB storage device after confirming the ACCESS indicator has disappeared in the function access area. 10. If necessary, confirm the firmware was correctly updated in the version field in the SETUP screen. Also, adjust the detection point of the touch screen (Calibration function) on the startup menu screen. Restart the M7CL first to adjust the faders (Calibration function). For details, refer to the M7CL Owner’s Manual. This completes the update procedure of the M7CL firmware. If you have backed up the necessary data, load it using the M7CL SAVE/LOAD function or the M7CL Editor (compatible with the updated firmware version). If a password has been set for Administrator, set the password again. If the firmware has been updated from V1, rotate the top panel MONITOR LEVEL knob slightly in either direction, since the monitor level has been reset to zero. Updating the firmware V3.0x to V3.0x, or V3.5x to V3.5x 1. Turn off the power to the M7CL. 2. Connect the USB storage device to the M7CL USB connector, then turn on the power to the M7CL. A .Start Loading ?. message will be displayed. 3. Click the OK button to start loading the firmware. CAUTION: A .Loading.... message will appear during loading the firmware. The indication ........ will be displayed during the loading progress. Do not disconnect the USB storage device or power-off the M7CL while accessing the USB storage device. 4. When the firmware has been loaded, power-off the M7CL, remove the USB storage device, then turn on the power to the M7CL while holding down the SCENE MEMORY [STORE] key. 5. When an .Initialize All Memories ?. message appears, press the INITIALIZE button. 6. When an .Are you sure ?. message appears, press the OK button. Initializing the internal memory will be started. 7. When the initialization is complete, press the EXIT button. 8. If necessary, confirm the firmware was correctly updated in the version field in the SETUP screen. This completes the update procedure of the M7CL firmware. If you have backed up the necessary data, load it using the M7CL SAVE/LOAD function or the M7CL Editor (compatible with the updated firmware version). If a password has been set for Administrator, set the password again. Updating the EtherSound module firmware (M7CL-48ES) For more information on the ES-Firmware Up...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M7CL-32 (260.14 kb)
Музыкальные инструменты - M7CL-48ES (260.14 kb)