Оценок - 2, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
NOTE • If you recall to a channel that is channel-linked, linking will be cancelled for the recalled channel. NOTE POST ON added as an insert / direct out position Insert is automatically turned on/off when GEQ insertion is enabled or cancelled Changed minimum value of the GATE threshold level 5 When you enable channel link, HA gain and fader operations will now be linked while maintaining the level difference between channels of the link group. . Temporarily defeating link For parameters (HA gain and fader) that preserve their relative level differences when linked, you can temporarily defeat linking for all linked channels, for example when you need to adjust the level balance between channels of a link group. Hold down the [SEL] key of the channel whose balance you want to adjust, and operate the parameter that you want to modify. While you’re holding down the [SEL] key, the HA gain and fader will not be linked. (However, temporary unlinking is not possible during the fade that occurs when a scene memory is recalled.) A monitor fader has been added to the monitor output level control, allowing you to use the STEREO MASTER fader / MONO MASTER fader to control the level. You can now also use the [ON] key of the MONO channel and STEREO channel to turn the monitor output on/off. A new MONITOR FADER field has been added in the MONITOR screen and the MONITOR popup window. [MONITOR screen] [MONITOR popup window] 1 MONITOR FADER LEVEL Indicates the current monitor fader. B FADER ASSIGN MODE button Each time you press this button of the MONITOR popup window, you will alternate between NONE > STEREO > MONO > NONE. If you select STEREO, you’ll be able to use the top panel STEREO MASTER fader to control the monitor fader. You can also use the [ON] key located above the STEREO MASTER fader to turn the monitor output on/off. If you select MONO, you’ll be able to use the top panel MONO MASTER fader to control the monitor fader. You can also use the [ON] key located above the MONO MASTER fader to turn the monitor output on/off. Channel link level differences maintained, and can temporarily defeated Using the STEREO/MONO MASTER fader to adjust the monitor output level 1 1 2 • The monitor fader and MONITOR LEVEL knob are located in series. The top panel MONITOR LEVEL knob is still valid even when you’re using this function to adjust the monitor level. The monitor signal will not be output if the MONITOR LEVEL knob is set to the minimum position. • The [ON] key of the STEREO channel or MONO channel will operate in tandem with the MONITOR screen’s OUTPUT button. The PHONES OUT jack will always output the monitor signal, regardless of whether the OUTPUT button is on or off. • You can also assign a user-definable key to switch the FADER ASSIGN MODE setting (p. 7). • The MONITOR button of the function access area is shown in red for STEREO or in yellow for MONO, depending on the FADER ASSIGN MODE setting. NOTE 6 “Global Paste” is a function that lets you copy and paste settings of the desired channel or parameter from the current scene to scene data in memory (multiple selections are allowed). This is a convenient way in which changes to the current scene can be applied to multiple scenes that have already been stored. 1 In the function access area, press the SCENE field to access the SCENE LIST window. 2 In the lower right of the SCENE LIST window, press the GLOBAL PASTE button to access the GLOBAL PASTE window. In this screen you can select the copy-source channels/ parameters and specify the paste-destination scene data. 3 Use the tabs to select the items to be copied from the following choices. 4 Select the copy-source channels and parameters. The display will depend on the tab you selected. You cannot select different parameters for each channel. Use the top panel [SEL] keys to select a channel. . INPUT tab Select the input channel in the upper left, and its parameters in the lower left. You can select the following parameters. . OUTPUT tab Select the output channel in the upper left, and its parameters in the lower left. You can select the following parameters. . RACK tab Select RACK 1–8. . PATCH/NAME tab Select from INPUT PATCH, INPUT NAME, OUTPUT PATCH, and OUTPUT NAME. 5 In the DESTINATION SCENE area, select the range of paste-destination scenes. The data will be pasted to all scenes in the range between FROM and TO. Use multi-function encoder 7 to select FROM, and multi-function encoder 8 to select TO. 6 Press the PASTE button. The selected items of the current scene will be pasted to the scene(s) in memory. A progress bar will be shown while the Paste operation is being performed. The STOP button is shown while the Paste function is being executed; you can stop by pressing this button. In this case, the Paste function will have been partially executed, and the data cannot be restored to its previous state. INPUT Input channels and parameters OUTPUT Output channels and parameters RACK RACK 1–8 PATCH/NAME Input/output...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M7CL-32 (2.02 mb)
Музыкальные инструменты - M7CL-48ES (2.02 mb)