Оценок - 3, средний балл: 3.7
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Reception must occur correctly whether or not the status byte is omitted. M7CL – Bedienungsanleitung MIDI-Datenformat MIDI-Datenformat PROGRAM CHANGE (Cn) Reception If [Program Change ECHO] is ON, bank select messages will also be echoed from MIDI OUT. If SINGLE CH is selected, these messages are received if [Program Change RX] is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are received regardless of the channel. When these messages are received, scene memory and effect library are recalled according to the settings of the [Program Change Table]. Transmission If [Program Change TX] is ON, these messages are transmitted according to the [Program Change Table] settings when scene memory and effect library are recalled. If SINGLE CH is selected, these messages are transmitted on the [Tx CH] channel. If the recalled scene memory and effect library has been assigned to more than one program number, the lowest-numbered program number for each MIDI channel will be transmitted. Program Change messages are not used for transmission to M7CL Editor because there is no guarantee that the contents of the assignment tables will match. (Parameter Change messages are always used.) You can choose either MULTI MIDI CH or SINGLE CH. If SINGLE is selected You can choose the RX CH, OMNI CH, and TX CH. You can choose whether a bank select message will be added. A bank of up to 16 can be specified. If MULTI is selected The RX and TX channels will be the same. The assignment table will use the settings for each MIDI channel. Bank select messages will not be added. You can make settings for up to sixteen MIDI channels. STATUS 1100nnnn Cn Program change DATA 0nnnnnnn nn Program number (0-127) 2 SYSTEM REALTIME MESSAGE 2.1 TIMING CLOCK (F8) Reception This message is used to control effects. This message is transmitted twenty-four times per quarter note. Echoing of this message depends on the OTHER item in the ECHO settings. STATUS 11111000 F8 Timing clock 2.2 ACTIVE SENSING (FE) Reception Once this message has been received, MIDI communication will be initialized (e.g., Running Status will be cleared) if no message is received for an interval of 400 ms. This message is not subject to echoing. STATUS 11111110 FE Active sensing 2.3 SYSTEM RESET (FF) Reception When this message is received, MIDI communication will be initialized (e.g., Running Status will be cleared). This message is not subject to echoing. STATUS 11111111 FF System reset 3 System Exclusive Message 3.1 Bulk Dump Command rx/tx function F0 43 0n 3E BB BB 11 D0 D1 D2 … rx/tx BULK DUMP EE F7 BULK DUMP DATA DATA F0 43 2n 3E 11 D0 D1 D2 F7 rx BULK DUMP BULK DUMP REQUEST REQUEST The M7CL uses the following data types for a bulk dump. Data name (D0) Data Number (D1,2) tx/rx function ,M‘ 0–300, 512, 768 tx/rx Szenenspeicher & Anforderung (Request) ,S‘ 512–517 tx/rx Szenenspeicher & Anforderung (Request) (aktuelles Setup) ,s‘ 512–528 tx/rx User-Setup-Speicher & Anforderung (Request) ,Y‘ 1–199, 512– tx/rx Dynamik-Library & Anforderung (Request) ,H‘ 0–199, 512–559, tx/rx Eingangskanalbibliothek & 560-567 Anforderung (Request) ,h‘ 0–199, 768–783, tx/rx Ausgangskanalbibliothek & 1024–1031, Anforderung (Request) 1280–1282 ,Q‘ 1–199, 512– tx/rx Eingangs-EQ-Bibliothek & Anforderung (Request) ,q‘ 1–199, 768– tx/rx AusgangsEQ-Bibliothek & Anforderung (Request) ,F‘ 1–199, 512– 527 tx/rx GEQ-Bibliothek & Anforderung (Request) ,E‘ 1–199, 512– 515 tx/rx Effekt-Library & Anforderung (Request) ,P‘ 512 tx/rx Programmwechseltabelle & Anforderung (Request) ,C‘ 512 tx/rx Controller-Tabelle & Anforderung (Request) ,M‘ 0–300 Szenennummer 512 Aktuelle Daten (ohne Recall Safe) 768 Aktuelle Daten (mit Recall Safe) ,S‘ 512 Setup Memory 513 Mischpulteinstellung 514 Ausgangs-Port 515 Monitor 516 MIDI-Einstellung 517 Library-Nummer ,s‘ 512–515 Anwenderdefinierte Tasten 1–4 516–519 Anwenderdefinierte Tasten (Gast) 1–4 520-523 Anwenderdefinierte Tasten (Admin) 1–4 524 Preference 525 Anwenderdefinierte Taste 526 Anwenderdefinierte Taste Gast 527 Preference Gast 528 Preference Admin ,Y‘ 1–199 Library-Nummer 512–559 Dynamik 1 Eingange 1–48 560–567 STIN 1L–4R 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) 1536-1583 Dynamik 2 Eingange 1–48 1584–1591 STIN 1L–4R ,H‘ 0–199 Library-Nummer 512–559 Eingange 1–48, 560–567 STIN 1L–4R ,h‘ 0–199 Library-Nummer 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) ,Q‘, ,q‘ 1–199 Library-Nummer 512–559 Eingange 1–48, 560–567 STIN 1L–4R 768–783 MIX 1–16 1024–1031 MATRIX 1–8 1280–1282 STEREO L,R,MONO(C) ,F‘ 1–199 Library-Nummer 512–527 RACK 1A–8B ,E‘ 1–199 Library-Nummer 512–515 RACK 5–8 ,P‘, ,C‘ 512 Aktuelle Daten Data is lost when you write to the preset library. The unique header (Model ID) identifies whether the device is a M7CL. To calculate the check sum, add the bytes starting with the byte after BYTE COUNT (LOW) and ending with the byte before CHECK SUM, take the binary complement, and set bit 7 to 0. CHECK SUM = ...
Эта инструкция также подходит к моделям:Музыкальные инструменты - M7CL-32 (16.68 mb)
Музыкальные инструменты - M7CL-48 (16.68 mb)