Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации HP, модель HP BL860c Dual Processor Server Blade

Производитель: HP
Размер: 317.3 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


Hardware and Software Installation Procedure
Step 1: Access the system card bay
Hardware and Software Installation Procedure
This document is for software version 2.0.15.0. These instructions apply to AD144A Windows/Linux 133MHz
PCI-X cards. The driver may be downloaded from the web at http://www.hp.com/support/itaniumservers.
If your 10GigE card is factory installed (ordered on product option 0D1), you do not need to perform
the hardware and software installation steps. You still need to configure the card IP address and possibly set
other parameters and options such as those mentioned in the Network Card Configuration worksheet.
The AD144A 10-gigabit Ethernet cards can be added to your system or replaced without the need to shut
down or reboot the system--a process called online addition and replacement (OLAR). The following
instructions assume you are not performing online addition and replacement.
Step 1: Access the system card bay

If the system is running, first, issue the sync command. Then, shut down the system by executing:
shutdown -h. Respond “y” to the continue to shutdown prompt.

Wait for the system to shut down completely, and then power off the system by pressing the system off
button. Ensure that the system is grounded.

Open the system to gain access to the PCI-X backplane.

Select an empty PCI-X slot and remove the slot cover.
NOTE
The AD144A card will perform best in PCI-X 133MHz “dual-rope” (or high performance)
slots. Please refer to the hardware users’ guide for each system for the location of the
dual-rope slots.
Step 2: Install the card

Check the latest 10 Gigabit Ethernet support matrix to see the systems that support this card, how many
cards per system, and if any software updates are needed, The support matrix is available on the web at
http://docs.hp.com under “I/O Cards and Networking Software.”

Observe the antistatic precautions. HP recommends wearing ESD straps when installing the card.

Record the serial number and MAC address located on the card for future reference.

Grasp the card by its edges or faceplate with both hands, insert the card into the slot, and firmly but
gently press the card in until it is fully seated.

Secure the card and reassemble the system.
Step 3: Connect the card to the network

Attach the network cable to the card. Attach the connector from a LAN cable to the card (Figure 1). For 10
GigE Base-SR, cabling can be either 62.5 micron or 50 micron multimode fiber optic (MMF) cable with LC
connectors. If the remote connection is type SC, you will need an LC-to-SC cable. Refer to the tables at the
end of this procedure for operating distances.

Attach the free end of the LAN cable to any unused port on the 10 GigE Base-SR switch. Ensure that the
switch is configured to support any new connections.
3


...

Эта инструкция также подходит к моделям:
Компьютеры - HP BL860c Single Processor Server Blade (317.3 kb)
Компьютеры - HP Integrity BL860c Carrier-grade Server Blade (317.3 kb)
Компьютеры - HP Integrity BL860c Server Blade (317.3 kb)
Компьютеры - HP Integrity rx5670 Server (317.3 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории