.. .................. ................ .... .................. ............ ............ .............. .......... ........ ...... ...................... .... .................... ........ ................ ................ ................ ............ .... ................ ...... .................. ...... ...... ............ .... ................ .... .................. ............ ............ .............. ...... .... ................ ...... .... .... .................. ...... .... ........

Shorting the battery terminals together may cause sparks, burns or a fire. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to Check for misalignment or binding of moving parts, breakage other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the model

Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Additionally, you can refer to the American National Standards Institute (ANSI) 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations. USE COMMON SENSE WHEN OPERATING THIS DRILL PRESS OR OTHER POWER TOOLS. Never try to perform drilling operations on work pieces that are too large to be clamped to the worktable or vises. Keep this ma

H HHo ool lld dd t tto ooo ool ll b bby yy i iin nns ssu uul lla aat tte eed dd g ggr rri iip ppp ppi iin nng gg s ssu uur rrf ffa aac cce ees ss w wwh hhe een nn p ppe eer rrf ffo oor rrm mmi iin nng gg a aan nn o oop ppe eer rra aat tti iio oon nn w wwh hhe eer rre ee t tth hhe ee c ccu uut ttt tti iin nng gg t tto ooo ool ll m mma aay yy c cco oon nnt tta aac cct tt h hhi iid ddd dde een nn w wwi iir rri iin nng gg. .. Contact with a “live” wire will also make exposed metal parts of the tool

If the unit is repaired, reconditioned replacement parts may be used. If Alltrade chooses the product, it may replace it with a new or reconditioned one comparable design. The repaired or replaced unit will be of the remainder of the warranty period. Typically, a defective product that is returned within the first 30 days after the purchase date will be replaced; for items returned after the first 30 days and within the warranty parts not subject to normal wear and tear or replaced, at Alltrade’

Keep your hands and feet well away from the work piece. Never feed the blade into the work piece until the blade is at full speed. If the blade is not at full speed, the saw may kick back causing serious personal injury. Use proper blade for the particular cutting application. • Put on eye protection. • Clear the saw of any foreign material. • Make sure the work piece is held securely in place. Hold smaller pieces in a • Mark out the line to be cut so it is easily visible. • Start inside the are

• Always keep the driver bit straight to prevent damage to the screw. • Hold the Drill with both hands to ensure control if the bit should stick or slip. • To prevent wood from splitting, drill pilot holes into the wood before driving in the screws. 14 VARIABLE SPEED TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH: • The speed of the Cordless Drill depends on the amount of pressure you put on the trigger. • The more pressure you apply, the faster the Cordless Drill will go. • Release

WARNING: Handling the power cord on this product may expose you to lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. 3 SAFETY RULES FOR IMPACT WRENCHES Use only impact sockets. Non-impact sockets may shatter or break causing injury and/or damage. Ensure fastener and/or system will withstand the level of torque generated by the tool. Excessive torque may cause bre

SYMBOL NAME EXPLANATION V Volts Voltage (Potential) A Amperes Current Hz Hertz Frequency (Cycles per Second) W Watt Power Kg Kilograms Weight Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal Class II Construction Denotes Double Insulation min Minutes Time s Seconds Time ! Diameter Size of Drill Bits, Grinding Wheels, etc. No load speed No-load Rotational Speed .../min Revolutions per Minute Revol

If any help and advice is needed, please contact us at 1-800-590-3723. Properly cared for, this tool will give you many years of satisfaction. IINNTTEENNDDEEDD UUSSEE This tool is intended for consumer use only. This tool is not designed for professional use. The power cord should only be used in approved electrical outlets as described in this manual. G GG E EE N NN E EE R RR A AA L LL S SS A AA F FF E EE T TT Y YY R RR U UU L LL E EE S SS F FF O OO R RR A AA L LL L LL E EE L LL E EE C CC T TT