Washer (2) 29 32-40-1241 Intermediate Gear 6 23-44-0060 Brush Retaining Screw (2) 30 06-42-0800 Woodruff Key 7 06-81-5800 6-32x5/16 Fil.Hd.Sem Sw. Mtg. Scrs. (2) 31 32-75-1601 Spindle Gear 8 28-50-4488 Motor Housing Assy. (Incl. Items 15,16&17) 32 06-42-1600 Woodruff Key 9 42- 68-0225 WireCI amp 33 36-66-2001 Intermediate Pinion Shaft ★ 10 23-66-0487 Switch 34 45-36-0210 Spindle Gear Spacer ★ 11 23-16-0660 Switch Insulator 35 02-04-0640 Bali Bearing 12 06-81-8625 6-32x1/4 Ground Screw

The tool speed can be controlled from minimum to maximum nameplate rated RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed (Fig. 1). "LOCK-ON" BUTTON The "Lock-ON" button, located in the handle of your tool allows for continuous operation at maximum RPM without holding the trigger. TO LOCK TRIGGER "ON": squeeze trigger, depress button and release trigger. TO UNLOCK THE TRIGGER: squeeze trigger and release it without dep

The technique is to start slowly, increasing the speed as the screw runs down. Set the screw snugly by slowing to a stop. Prior to driving screws, pilot and clearance holes should be drilled. FASTENING WITH SCREWS This procedure shown in (Fig. 5) will enable you to fasten materials together with your Cordless Drill/Screwdriver without stripping, splitting or separating the material. First, clamp the pieces together and drill the first hole 2/3 the diameter of the screw. If the material is soft,

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area When operating a power tool outside, use an outdoor extension cord marked "W-A" Keep your work area clean and well lit. or "W." These cords are rated for outdoor use Cluttered benches and dark areas invite and reduce the risk of electric shock. Refer to accidents. “Recommended sizes of Extension Cords” in Do not operate power tools in explosive the

POWER INDICATOR LIGHT Model number 11241EVS 11248EVS Shank style SDS Max Spline Maximum Capacities: Carbide tipped bits 1 9/16" 1 9/16" Thick wall core bits 4" 4" SPLINE TOOL HOLDER (Model 11248 only) FIG. 1 BM 1619929548 2/03 2/12/03 12:37 PM Page 6 BM 1619929548 2/03 2/12/03 12:37 PM Page 7 Operating Instructions INSTALLING ACCESSORIES Clean the insert shank end of the accessory to remove any debris, then lightly grease with a light oil or lubricant. Insert accessory into the tool holder, whil

SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Electrical Safety Double Insulated tools are equipped with a polarized plug (o

Enduisez le pivot d’une mince couche de graisse MILWAUKEE de type «E». 3. Replacez le manchon sur le pivot. assurez-vous que le manchon du pivot tourne librement sur le pivot et ensuite, remettez l’anneau de retenue en place. page 26 Remplacement du joint d’etancheite des coussins a vide Pour les modeles 4115, 4125 et 4130 seulement. A l’usage normal, le joint d’etancheite en caoutchouc sous le coussin a vide vient a s’user et il faut le remplacer. Faites remplacer le joint d’etancheite du couss

Such preventive safety measures reduce the risk of starting the tool accidentally. Cordless Impact Drivers and Impact Wrenches FIG. 1 VARIABLE SPEED TRIGGER SWITCH FORWARD/REVERSING LEVER & TRIGGER LOCK RUBBERIZED GRIP BATTERY RELEASE TABSBATTERY PACK VENTILATION OPENINGS BRUSH COVER LOCKING SLEEVE BELT CLIP (Optional Accessory) SWIVEL LIGHTING SYSTEM BIT AND BIT STORAGE 1/2" SQUARE DRIVE (Models 22612, 22614 & 22618 only) Model number 22612 22614 22618 Voltage rating 12 V 14.4 V 18 V No load sp