COM WWW. MAYTAG. CA EN CANAl)A, WWW.MAYTAG.CA W10057351A ,i_!_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_i_i_ii!i.i!i!i!i!i!i!i!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_iiiiiiiiiii//li'ii_i_iil,,i_i!i!i_,_. _._._..ii_ii_ii.il.ii .ii.ii.ii.ii_iil_i_iil.iiiii_ii]ii_i@iii@iiiiii;iiiiii;;;;;;;;;;;;;;;;;;;;;;;i_!i_ii_!_!i .il.iiii_ii,i_ii,i_ii,i_ii,i_ii,i_@ii_i_iil....'.'_''_'_'_'_'_'_'_'_'_'_'_'_'_'_'_'_.I.I.ii 'ii'ii'i'ii'ii'i'ii'ii_,:,ii,i,l,ii_ii_:ii._:ii._:ii.@_ill_._!iiiiiii@il_ii

W10201177B TABLE OF CONTENTS DRYER SAFETY..........................................................................................................................3 INSTALLATION INSTRUCTIONS.............................................................................................5 Tools and Parts.......................................................................................................................5 Location Requirements .........................................................

1.The Dryness Level settings cannot be changed while the dryer is running. 2.Press and hold the DRYNESS LEVEL button for 5 seconds. The dryer will beep, and “CF” will be displayed for 1 second followed by the current Dryness Level setting. 3.To select a new Dryness Level setting, press the DRYNESS LEVEL button again until the desired Dryness Level setting is shown. NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash. 4.Press START/PAUSE

18 Para una version en espanol, visite: Numero de pieza W10267625A TABLE OF CONTENTS Page DRYER SAFETY..............................................................................................2 QUICK START GUIDE/DRYER USE..............................................................4 Drying and Cycle Tips...............................................................................6 Cycles.......................................................................................................

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 1 .. ." (3.8 cm) from 3 remaining wires. Strip insulation back 1" ( 2.5 cm). Shape ends of wires into a hook shape. (2.5 cm) 5"(12.7 cm) When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block ( hook facing right), squeeze hooked end together and tighten screw, as shown. 1. Remove center silver-colored terminal block screw. 2. Remove neutral

¦Select the desired Options. To make changes during a Sensor Cycle: ¦Press START/PAUSE. ¦Adjust Dryness Level. NOTE: Dryness selections can be made only while using Sensor Cycles. How the Sensi-Care™ Drying System Works Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast the load is drying, how hot the air should be, and when clothes are dry. The system automatically stops the cycle to help save time and avoid overdrying. To use a Timed Cycle ¦Turn knob to desi

11 Dryer Controls At A Glance..............................12-13 Dryer Operating Tips............. 14 Dryer Exhaust Tips.................15 Replacing the Drum Light... 16 Reversing the Dryer Door.... 16 Water Use................................. 17 Care and Cleaning.................17 Storing the Maytag Neptune™ Super Stack.......... 17 Washer Operating Sounds.......................................18 Before You Call..................19-21 Warranty......................Back Page MAYT

COM WWW.MAYTAG.CA EN CANADA, WWW.MAYTAG.CA W10139629A TABLE OF CONTENTS DRYER SAFETY. .............. ............. .............. .............. .............. 3 INSTALLATION INSTRUCTIONS ............. .............. .............. 4 Tools and Parts............ ............. .............. .............. .............. 4 Optional Pedestal........ ............. .............. .............. .............. 4 Location Requirements............. .............. .............. .............. 5 Electric

¦ Do not use an exhaust hood with a magnetic latch. Improper venting can cause moisture and lint to collect indoors, which may result in: Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc. Housecleaning problems and health problems. 11 Plan Vent System Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D A E F G H A. Dryer E. Clamps B. Elbow F. Rigid me

See “ Electrical Requirements.” ¦ A sturdy floor to support the total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered. ¦ Cold water faucets located within 4 ft (1.2 m) of the water fill valves, and water pressure of 20-100 psi (138-690 kPa). You may use the water supply for your washer using the “Y” connector and short hose (if needed) which are provided. ¦ 20-100 psi (138-690 kPa) for best performance. ¦ A level floor with a m